## ## ##### ## ## ## ## #####
_____ | _ | | | | | | | | | \ \_/ / \___/
_ ( ( /| | \ ( | | \ | | | (\ \) | | | \ | | ) \ | |/ )_)
____ | _ \ | |_) | | _ < | |_) | |____/
IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now. Visit Preferences to set your user name Summary of change: This concerns C004 trigger with cam sync. I have an engine with a problem with recent firmwares, it's a Volvo 4 cyl that has 2 teeth on the front accessory pulley and camsync on the intermediate shaft (rotates at cam speed). It uses a wasted spark coilpack for ignition so it needs the cam sync. It ran with 1.0.73 for a long time, then I upgrade to 1.1.79 a little less than a year ago, and this setup was tuned and worked. Here comes the problem, we wanted the new features with injector angle curve that came with 1.1.80, so upgraded to 1.1.88 as it would be really interesting to tune the injector angle curve as it is an Alpha-N tuned engine with lots of valve overlap, Speed-Density doesn't work well except for full throttle (no good pressure signal). A very apparent problem appeared, I could not get any RPM signal. It was zero at all times, **except when I disabled cam sync as a test**. The "Running On/off" status flag flashes when the primary trigger has events, but RPM = 0. The triggerlog looks just clean and healthy - and why shouldn't it, all we changed was firmware. I tried downgrading from 1.1.88 to 1.1.81, same results. RPM only returned with disabled cam sync. * Triggerlog, a bit short, but looks ok : [http://www.vems.hu/files/MembersPage/MattiasSandgren/C004andCamSync/c004-camsync-issue.triggerlog.txt c004-camsync-issue.triggerlog.txt] ** is it possible that something prevented sparks or injection (and starting) at the time the triggerlog was captured ? Like fuse, or ign/INJ connector removed ? * The 1.1.88 config : [http://www.vems.hu/files/MembersPage/MattiasSandgren/C004andCamSync/1.1.88.vemscfg 1.1.88.vemscfg] Config files for 1.1.79 (original that ran) and all files are here : http://www.vems.hu/files/MembersPage/MattiasSandgren/C004andCamSync/ I will downgrade to an earlier 1.1.7x if this doesn't work out as it did work with 1.1.79, but I'll use 1.1.78 since 1.1.79 is not available and was only uploaded about a year ago because it had just become available (and later removed). We tested 1.1.88 (and 1.1.90) on bench with C004 + cam sync config. * found no misfire or mistimed ignition. We even turned RPM down to 63 RPM and RPM detection and ignition was OK. * when we disturbed the signal both 1.1.88 and 1.1.90 recovered normally the signal recovered ** triggerlog will need to be recaptured with the new firmware as instructed privately. This will also log the ignition events in the same file with triggerlog input events. On bench it worked wonderfully (and re-confirmed the . What can be different on bench and on real engine ? * Maybe something about the camsync position vs configured min/max values ? * maybe something around the outputs ? Like a relay not powering some coils / injectors ? ** even without this, if the signal is good, RPM detection should work * another possible reason: '''output => inputtrigger interference''' ** also disconnect wideband Optional: Add document to category: Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.