/\    
    /  \   
   / /\ \  
  / ____ \ 
 /_/    \_\
           
           

     _    
    / \   
   / _ \  
  / ___ \ 
 /_/   \_\
          

         
         
  ####   
 ##      
 ##      
 ##      
  ####   
         

         
         
  #####  
 ##  ##  
 ##  ##  
  #####  
     ##  
     ##  

 _______ 
(  ____ \
| (    \/
| (__    
|  __)   
| (      
| (____/\
(_______/
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
'''Ignition Setup''' for MembersPage/MarteleurTim Tim will describe the engine basics (like cyl-count, etc...) on MembersPage/MarteleurTim page to make it possible to help. I keep distributor only for distribution. I use Hall sensor on crank as a trigger input for the VEMS. Q: So actually I have to lock the plate in the distributor and remove the vacuumline in order to lock the vacuumadvance and let the distributor only distribute the spark? A: With the distributor used only for spark distribution, and not timing advance, none of what you described is necessary. The poles in the rotor cap are fixed, that is all that matters for spark distribution. I have setup the wheel with two bolts 180° separated and +- 60°BTDC.Picture will follow. ---- '''Config''' see MembersPage/MarteleurTim/Config * How do I determine the correct amount of degrees the trigger passes the sensor before the crank reaches TDC? ** remove a sparkplug so you can measure the piston height with a screwdriver or micrometer gauge. Rotate the engine slowly *** with wrench, from the crank (not cam!) *** or by moving the car, in gear 5 OK but then I still have to measure with a degreestool the exact amount of degrees the trigger is from TDC. This is not so easy to determine whether it is 60° or 61° or 58°? Measure the white dot (paint one if there is none) position precisely, and the trigger position only roughly. The dot is 0..10 degrees BTDC, quite easy to measure. This allows you to adjust the ign_tdcdelay with a TimingLight. You can also use permanent marker pen and use length-measuring tool (eg. at the circumference of a wheel) and calculate degrees. OK thanks I will do that. Some Q's about the first config based on a similar engine of Mattias volvo * req_fuel=73# req-fuel for 4cyl engine 1755cc and 149cc injectors ** 0x73=115 = 11.5 msec is '''awfully lot'''. Half the req_fuel, so the VE values are doubled: 0..200 is better precision than 0..100 ** #req_fuel = 6.49 x (D/N/I) = 6.49 x (1755/4/149)= 19.1ms. This is even worse * divider=01# 4 injectorbanks * alternate=03 * kpafac=7D # 250 kPa MAP sensor * kpaoffs=6B * injopen=00 # keep this 00 * battfac=10 * injocfuel=15 # 21*24usec is a bit too low, 800..1000 usec is a better starting value ** but it depends on flyback, so you want to write about it (powerflyback, low-voltage, high-voltage) if you really want to finetune (it should not be critical unless with very big injectors) * injrampup_battfac=FF * injpwm=FF * injpwmt=FF # PWM-ing disabled * injpwm6=00 *iac_step_seq=C9 *iac_conf=10 # disable the air-valve based iac (with precise_idle off bit3=0, iac_sol_channel is simply switched on/off slowly, not PWM-ed; but iac_sol_channel is disabled with FF, so no output is altered), only ignition advance based active (00 disables ignition-adjust as well, use that initially) *iac_max_steps=E8 *iac_tps_thres=05 *iac_cold_idle_temp=A0 *iac_warm_idle_temp=D0 *iac_cold_rpm=65 *iac_warm_rpm=4F *iac_cold_start_pos=FF *iac_warm_start_pos=FF *iac_afterstart_rpm=0C *iac_afterstart_duration=FF *iac_afterstart_steps=00 *iac_kp=25 *iac_ki=10 *iac_kd=30 *iac_integral_speed=C0 *iac_integral_limit_dec=33 *iac_integral_limit_inc=E4 *iac_integral_deadband=0A *iac_deadband=05 *iac_pid_conf=01 *iac_overclose_interval=FF *iac_ref_pos[0]=60 *iac_ref_pos[1]=5C *iac_ref_pos[2]=58 *iac_ref_pos[3]=50 *iac_ref_pos[4]=4C *iac_ref_pos[5]=48 *iac_ref_pos[6]=38 *iac_ref_pos[7]=31 *iac_ref_pos[8]=2F *iac_ref_pos[9]=2E *iac_sol_channel=FF # disable iac solenoid output *iac_ign_advance_change=10 *iac_ign_retard_change=10 *iac_ign_advance_limit=10 *iac_ign_retard_limit=18 *iac_ign_threshold=08 ---- '''Tables''' see MembersPage/MarteleurTim/Tables I want injector sequence h[0]= 2 8 4 1 0 0 0 0 I have connected FETdrivers:A B C D to EC36pin 7 19 8 20 Q: Does this correspond with my config and tables?
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.