## ## #### ## #### ## ##
_______ (_____ ) /'/' /'/' /'/'___ (_______)
### ## ## ## ## ## ####
___ ( _`\ | | ) | | | | ) | |_) | (____/'
_ __ | |/ / | ' / | < | . \ |_|\_\
IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now. Visit Preferences to set your user name Summary of change: Subpage of MembersPage/MarcellGal/WoodGasifierEngine '''Crysler Magnum 5.2L V8 engine wiring'''. Engine is running. (V8 has nice sound). Some texts are in Hungarian ---- '''ignition output''' - currently using 1 distributer Ignition coil primary is connected between: * EC36/36 ign coil- * +12V Fuse (Biztosíték fontos!): 4-7.5A ---- '''Sensors''' * primary trigger HALL (8 window on crank), EC36/27 ** Nr of tooth on wheel: 16 ** edge: falling, 50 degrees TDCdelay (verified with strobe) * secondary trigger HALL (1 window on cam), EC36/13 ** edge: falling * internal MAP (csovel csatlakozik a MAP) '''TPS sensor''' * EC36/1 TPS signal (this was only wrong in the sent .xls or connected wrong ?) * EC36/29 TPS +5V * EC36/26 TPS ground (signal GND) ---- '''Stepper outputs''' coil1: (resistance= ?) * EC18/.. * EC18/.. coil2: (resistance= ?) * EC18/.. * EC18/.. 4 vezetékes léptetőmotor tekercsei kimérhetők: A-B C-D szerint kell bekötni az EC18-ba. * Stepper A EC18-pin4 * Stepper B EC18-pin10 * Stepper C EC18-pin5 * Stepper D EC18-pin11 Ezután csak 2 variáció marad. Ha az iránya szerint fordítottan reagál, akkor vagy az A-B megfordításával, vagy szoftveres konfigurálással orvosolható. ---- '''LCD''' - GenBoard/BuildProcedures/LCDconnect * DSUB9 / 5 is GND. ** verify that the header pin it is connected is 0 Ohm to EC36/26 (rádugás ELŐTT ellenőrizni, hogy a EC36/26-ra fog menni) ---- '''Install initial steps''' * download http://www.vems.hu/download/v3gui/ ** '''vemstune 2010-04-28''' (not 2009-10-02) ** if things don't go smooth, we'll need to try different version, but let's start with this ** install RS232 driver. if pl2303 than prolific.com.tw ** even if it was COM4 it might change when USB cable inserted into other USB port (see windows device manager, com ports = eszközkezelo) ** http://www.prolific.com.tw/eng/FAQs.asp?ID=50 ** http://www.prolific.com.tw/eng/downloads.asp?ID=31 ** [http://www.prolific.com.tw/support/files/\IO Cable\PL-2303\Drivers - Generic\Windows\allinone\PL2303_Prolific_DriverInstaller_v1210.zip v1210driver.zip] * TerminalProgram - to verify RS232 ** [http://hw-server.com/software/termv19b.html Bray-terminal] is very good (hyperterm is very bad) but any could work. ** 9600,8,n,1 (flow control: off) Choose comm port, Connect, Type "Man mdv mdV mci" as an experiment ** even if these * start VemsTune * set serial port (might need to restart vemstune) * take note of the firmware version (firmware info) * Tools / firmware / upload '''firmware 1.1.75 (non-PS2)'''. (because firmware 1.1.27 somehow misfired for the slightest noise on testbench) ** MAT= NTC:2252 ** coolant=NTC:2252 * download this [http://www.vems.hu/files/MembersPage/MarcellGal/GasMotor/CryslerMagnum5.2LV8/v3.3_n002248-2010.06.05-1_c016initial.vemscfg initial config] * upload config (select the just downloaded file) * reboot * verify MAP (must be 101 kPa) ** MAP calibration: select MAP sensor range 104, 250, 304 or 416 (so MAP is close to 101) ** finetune MAP sensor offset (so MAP=101) * verify TPS: ** from 0 .. max ** write down min and max TPS values * verify that angular width of tooth is 180 (in the old vemstune that means 45 degrees, tooth_wheel_twidth1=B4) Optional: Add document to category: Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.