###   
  ## ##  
  ##     
 ####    
  ##     
  ##     
 ####    
         

 ###     
  ##     
  ##  ## 
  ## ##  
  ####   
  ## ##  
  ##  ## 
         

 _     _ 
( )   ( )
`\`\_/'/'
  `\ /'  
   | |   
   (_)   
         
         

   ##    
         
  ###    
   ##    
   ##    
   ##    
  ####   
         

 ___   
(  _`\ 
| (_(_)
|  _)_ 
| (_( )
(____/'
       
       

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
Subpage of MembersPage/MarcellGal/WoodGasifierEngine '''Crysler Magnum 5.2L V8 engine wiring'''. Some parts are in Hungarian ---- '''ignition output''' - currently using 1 distributer Ignition coil primary is connected between: * EC36/36 (not 26 !!!!!!!!!!!!!!!!!!!!!!) ign coil- * +12V Fuse (Biztosíték fontos!): 4-7.5A ---- '''Sensors''' * primary trigger HALL (8 window on crank), EC36/27 * secondary trigger HALL (1 window on cam), EC36/13 * internal MAP (csovel csatlakozik a MAP) '''TPS sensor''' * EC36/1 TPS signal (this was only wrong in the sent .xls or connected wrong ?) * EC36/29 TPS +5V * EC36/26 TPS ground (signal GND) ---- '''Stepper outputs''' coil1: (resistance= ?) * EC18/.. * EC18/.. coil2: (resistance= ?) * EC18/.. * EC18/.. ---- '''Install initial steps''' * download http://www.vems.hu/download/v3gui/ 2010-04-28 ** if things don't go smooth, we'll need to try different version, but let's start with this ** install RS232 driver. if pl2303 than prolific.com.tw ** http://www.prolific.com.tw/eng/FAQs.asp?ID=50 ** http://www.prolific.com.tw/eng/downloads.asp?ID=31 ** http://www.prolific.com.tw/support/files/\IO Cable\PL-2303\Drivers - Generic\Windows\allinone\PL2303_Prolific_DriverInstaller_v1210.zip * TerminalProgram - to verify RS232 ** [http://hw-server.com/software/termv19b.html Bray-terminal] is very good (hyperterm is very bad) but any could work. ** 19200,8,n,1 (flow control: off) ** even if these * start VemsTune * set serial port (might need to restart vemstune) * take note of the firmware version (firmware info) * Tools / firmware / upload firmware 1.1.27 (16x14) ** MAT= NTC:2252 ** coolant=NTC:2252 * download config from ... * upload config (select the just downloaded file) * reboot * verify MAP (must be 101 kPa) ** MAP calibration: select MAP sensor range 104, 250, 304 or 416 (so MAP is close to 101) ** finetune MAP sensor offset (so MAP=101) * verify TPS: ** from 0-max take note of values
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.