_____ 
 | ____|
 |  _|  
 | |___ 
 |_____|
        

 _____ 
(_   _)
  | |  
  | |  
  | |  
  (_)  
       
       

 _   _ 
( ) ( )
| | | |
| | | |
| \_/ |
`\___/'
       
       

         
         
  ####   
 #    #  
 #    #  
 #    #  
  ####   
         

 ______  
(  ___ \ 
| (   ) )
| (__/ / 
|  __ (  
| (  \ \ 
| )___) )
|/ \___/ 
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
'''Electronic problems on the way - during MembersPage/MarcellGal/EngineSwap''' I think that collecting these experiences can be useful. There are many things to watch out for, easy to overlook something. '''Problems related to existing harness''' It's now obvious that working with an existing harness is harder than make one from scratch. I decided to use it for the connectors that I didn't have separately. It's a good idea to make a more detailed review and documentation of any existing harness than on MembersPage/MarcellGal/EngineSwap/DaewooHarness. Describe and categorize all connectors and their hidden connections, even the ones you know nothing about. ||'''Problem''' ||'''Effect''' || ||bad identification of car's node15 and node30|| delay with the starter motor. Starter motor and generator had to be connected after engine in place: harder|| ||using AC refrigerant pressure sender connector on TPS||ruined MAP sensor due to reverse supply|| || bad grounding due to unknown connections in the daewoo harness || delay (not yet fixed) || || forgotten injector supply wire. After some minor rewiring and some change in external circumstances (temperature) engine did not start. It barfed a little, and sparkplugs were wet. This was confusing. Running detailed checklist revealed the problem in first minute, since very first step was measuring with DVM if ECM sees injectors: it did not, because of forgotten injector supply.Stupid mistake, isn't it?||delay|| '''Problems related to v3.1 board''' Remember I used an old leftover v3.1 board (v3.2 is higher quality and higher assembly level) that failed the tests. I thought I can solder by heart and jump over most of the tests because I know the board very well. But I can make mistakes. ||'''Problem''' ||'''Effect''' || ||stepper259 chip's reset resistor was not soldered||minor delay|| ||510 Ohm and 100k swapped at pump1|| delay|| ||nernst1 amplified not amplifying (killed by static electricity)|| delay || ||injector channel tests failed. In fact the channels operated OK from the start, I just forgot to consider that the lookup from h[0] takes place and issued the wrong mdh.. command|| delay|| Unfortunately after getting up from my chair, I sparked (discharged) onto the board with my finger. It was a '''loud audible''' (and I felt it too) '''spark due to static electricity''' (the chair and my slippers helped build up voltage). It was so powerful that we first thought it was from an ignition coil, but there was no coil connected at all. It was no fun. We tested the functions, to see if anything is ruined. Fortunately the AVR and most functions survived, but the nernst1 OPA channel died. The pump- OPA channel in the same OPA survived. I connected the nernst1 signal directly to the AVR input (bypassing the nernst1 channel), and reconfigured the controller in config.txt for the lower wbo2_ri_target and higher wbo2_nernstdc_target. Surprisingly, the wbo2 heater control worked well even though the input voltage became 1/4 of original. I'll log the heater-control behaviour after this change in the car, but I'm confident that it'll be OK. '''Always touch the ground connection before getting close to the board to avoid harming the board with static discharge.''' In fact there were no problems with the board, just my negligence when completing (in a hurry). With v3.2 much less steps are needed with less chance of errors. ---- '''See also''' * MembersPage/MarcellGal/EngineSwap
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.