#####  
 ##  ##  
 ##  ##  
  #####  
     ##  
     ##  

 _       
( \      
| (      
| |      
| |      
| |      
| (____/\
(_______/
         

         
         
 ######  
  ##  ## 
  ##     
  ##     
 ####    
         

         
         
 ##   ## 
 ## # ## 
 ####### 
  #####  
  ## ##  
         

         
         
 ##  ##  
 ##  ##  
 ##  ##  
 ##  ##  
  #####  
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
== Audi urS4 1992 with the AAN engine == ||http://www.bonnquattro.se/images/eja/bild1_400.jpg||http://www.bonnquattro.se/images/eja/aan_1.jpg|| '''My goal is for now:''' * use all original sensors * replace the MAF with a MAP * replace the original Lambda with a WideBand Bosch LSU4.2 (7200) if possible * make my own electrical loom/harness for the engine, using VAG OEM connectors and Econoseal connectors on the Vems. * Make the engine run nice and good. * make it work with COPs from 1998-2007 VAGs, 06B905115L, logic-level ** Guide for conversion from original POS/coil to COP here: ** http://www.bonnquattro.se/aan/18tCoilPackConversionInstructions.pdf ---------------- '''What I know:''' * I will buy the assembled vems with econoseal connectors * I need 5 logic outputs for the ignition, would like a 3+5 version * The extra flyback 30v diode seems like a good choice * I will buy a wideband lambda * I will buy a EGT sensor * I want the LED (4x20?) * I want a special lambda display * EGT and knock sensors(would like to use the stock knock sensors) * onboard MAP sensor 400 kpa * I will buy some econoseal connectors 18+36 * Primary trigger Is VR * Secondary trigger would be "audi trigger" '''What I dont know:''' Q: Shall I order 2+6 version, what can I use the 2 high current outputs for ? A: Lots of things. Relay, solenoid, NOS, ... Q: How about firmware and sensors, do I need to compile something myself ? A: no need to compile anything. See VemsTune Q: I suppose I should choose PS2 connector as well A: useful eg. for wheel-speed input (but we can connect PS2 clock signal to an unused pin as well -------------------- ''' VEMS info ''' (I have bought a VEMS that came with this info:) Board_version=v3.3 Serial_nr= 2267 pump-= 4.05V wbo2_pump_pw_zero=0x64 wbo2_nernstdc_target=0x87 pump+= -1.0mV/200 Ohm AREF=4.9V (C103=1nF, no D100) --------------------- ''' Other project info ''' I have bought a engine loom from a -02 VW passat that will fit the COPs. Purchased a used WBO Bosch LSU 4.2 7090/91 as per below. Will start making the new COP work with the OEM ECU to begin with. --------------------- Time frame: 2016-01-18 I have begun installing this now. I will make an adapter cable to fit the Motronic 55 connector at first. When I have it all working I will make a new wireloom. Maybe I will wait until nex engine takes it place in the car. I started out connecting the Vems on bench to my PC so I could update FW. It turned out I '''needed to "lock" the CPU with direct ISP programming'''. It worked nice but now I cannot update bootloader further because of "access denied". I have got the password from VEMS, thanks! Upgrading the FW was no problem when having that :-) 2016-06-19: I need to update my config files from the old maps 12x12 to new ones 16x16 and maybe some other stuff. Im researching this topic right now. I have put together cable for the LCD and tested it out. https://youtu.be/nF_bM1gTyVo I also fixed Bluetooth connection so I can connect to it in the car later on. I also bought a cheap android pad and tested VEMSdisplay, very good! I like it alot! :-) --------------------- ''' Questions ''' ''2016-06-26'' I have no trigger input at all using triggerlog! :-( I have Firmware v1.2.31 And this is taken from configfile: primary_trigger=C3 secondary_trigger=19 tooth_wheel=1E trigger_tooth=00 another_trigger_tooth=06 lcd_analin=67 tooth_wheel_twidth[0]=00 tooth_wheel_twidth[1]=60 cam_sync_r_edge_phase=01 cam_sync_f_edge_phase=02 reset_engphase_after=F0 Is that correct? Have search forum and wiki but not really found any walk through of setup the triggers, that is up to date with this firmware. Also used built in help in vemstune.
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.