##  
     ##  
  #####  
 ##  ##  
 ##  ##  
  #####  
         

         
         
  ####   
     ##  
  #####  
 ##  ##  
  #####  
         

 _   _ 
| | | |
| | | |
| | | |
| |_| |
 \___/ 
       
       

         
         
 #####   
 ##  ##  
 ##      
 ##      
 ##      
         

         
         
 #####   
 ##  ##  
 ##  ##  
 #####   
 ##      
 ##      

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
== Audi urS4 1992 with the AAN engine == ||http://www.bonnquattro.se/images/eja/bild1_400.jpg||http://www.bonnquattro.se/images/eja/aan_1.jpg|| '''My goal is for now:''' * use all original sensors * replace the MAF with a MAP * replace the original Lambda with a WideBand Bosch LSU4.2 (7200) if possible * make my own electrical loom/harness for the engine, using VAG OEM connectors and Econoseal connectors on the Vems. * Make the engine run nice and good. * make it work with COPs from 1998-2007 VAGs, 06B905115L ** Q: is that power-input ? (not logiclevel) ? ** A: they are logic-level, 5v (not sure if its postive (+) though) ** Guide for conversion from original POS/coil to COP here: ** http://www.bonnquattro.se/aan/18tCoilPackConversionInstructions.pdf '''Next goal:''' * switch exhaust header * another turbo * larger injectors * another WasteGate * switchable fuel maps ---------------- '''What I know:''' * I will buy the assembled vems with econoseal connectors * I need 5 logic outputs for the ignition, would like a 3+5 version * The extra flyback 30v diode seems like a good choice * I will buy a wideband lambda * I will buy a EGT sensor * I want the LED (4x20?) * I want a special lambda display * EGT and knock sensors(would like to use the stock knock sensors) * onboard MAP sensor 400 kpa * I will buy some econoseal connectors 18+36 * Primary trigger Is VR * Secondary trigger would be "audi trigger" '''What I dont know:''' Q: Shall I order 2+6 version, what can I use the 2 high current outputs for ? A: Lots of things. Relay, solenoid, NOS, ... Q: How about firmware and sensors, do I need to compile something myself ? A: no need to compile anything. See VemsTune Q: I suppose I should choose PS2 connector as well A: useful eg. for wheel-speed input (but we can connect PS2 clock signal to an unused pin as well -------------------- ''' VEMS info ''' (I have bought a VEMS that came with this info:) Board_version=v3.3 Serial_nr= 2267 pump-= 4.05V wbo2_pump_pw_zero=0x64 wbo2_nernstdc_target=0x87 pump+= -1.0mV/200 Ohm AREF=4.9V (C103=1nF, no D100) --------------------- ''' Other project info ''' I have bought a engine loom from a -02 VW passat that will fit the COPs. Purchased a used WBO Bosch LSU 4.2 7090/91 as per below. Will start making the new COP work with the OEM ECU to begin with. --------------------- Time frame: 2016-01-18 I have begun installing this now. I will make an adapter cable to fit the Motronic 55 connector at first. When I have it all working I will make a new wireloom. Maybe I will wait until nex engine takes it place in the car. I started out connecting the Vems on bench to my PC so I could update FW. It turned out I '''needed to "lock" the CPU with direct ISP programming'''. It worked nice but now I cannot update bootloader further because of "access denied". I have got the password from VEMS, thanks! Upgrading the FW was no problem when having that :-) 2016-06-19: I need to update my config files from the old maps 12x12 to new ones 16x16 and maybe some other stuff. Im researching this topic right now. I have put together cable for the LCD and tested it out. https://youtu.be/nF_bM1gTyVo I also fixed Bluetooth connection so I can connect to it in the car later on. I also bought a cheap android pad and tested VEMSdisplay, very good! I like it alot! :-) --------------------- ''' Questions '''
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.