##  ##  
 ##  ##  
 ##  ##  
  #####  
    ##   
 ####    

 _____ 
|  _  |
| | | |
| | | |
\ \/' /
 \_/\_\
       
       

 __   __
 \ \ / /
  \ V / 
   | |  
   |_|  
        

         
         
  ####   
     ##  
  #####  
 ##  ##  
  #####  
         

   #     
   #     
 #####   
   #     
   #     
   #  #  
    ##   
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
== Audi urS4 1992 with the AAN engine == ||http://www.bonnquattro.se/images/eja/bild1_400.jpg||http://www.bonnquattro.se/images/eja/aan_1.jpg|| '''My goal is for now:''' * use all original sensors * replace the MAF with a MAP * replace the original Lambda with a WideBand Bosch LSU4.2 (7200) if possible * make my own electrical loom/harness for the engine, using VAG OEM connectors and Econoseal connectors on the Vems. * Make the engine run nice and good. * make it work with COPs from 1998-2007 VAGs, 06B905115L ** Q: is that power-input ? (not logiclevel) ? ** A: they are logic-level, 5v (not sure if its postive (+) though) ** Guide for conversion from original POS/coil to COP here: ** http://www.bonnquattro.se/aan/18tCoilPackConversionInstructions.pdf '''Next goal:''' * switch exhaust header * another turbo * larger injectors * another WasteGate * switchable fuel maps ---------------- '''What I know:''' * I will buy the assembled vems with econoseal connectors * I need 5 logic outputs for the ignition, would like a 3+5 version * The extra flyback 30v diode seems like a good choice * I will buy a wideband lambda * I will buy a EGT sensor * I want the LED (4x20?) * I want a special lambda display * EGT and knock sensors(would like to use the stock knock sensors) * onboard MAP sensor 400 kpa * I will buy some econoseal connectors 18+36 * Primary trigger Is VR * Secondary trigger would be "audi trigger" '''What I dont know:''' Q: Shall I order 2+6 version, what can I use the 2 high current outputs for ? A: Lots of things. Relay, solenoid, NOS, ... Q: How about firmware and sensors, do I need to compile something myself ? A: no need to compile anything. See VemsTune Q: I suppose I should choose PS2 connector as well A: useful eg. for wheel-speed input (but we can connect PS2 clock signal to an unused pin as well -------------------- ''' VEMS info ''' (I have bought a VEMS that came with this info:) Board_version=v3.3 Serial_nr= 2267 pump-= 4.05V wbo2_pump_pw_zero=0x64 wbo2_nernstdc_target=0x87 pump+= -1.0mV/200 Ohm AREF=4.9V (C103=1nF, no D100) --------------------- ''' Other project info ''' I have bought a engine loom from a -02 VW passat that will fit the COPs. Purchased a used WBO Bosch LSU 4.2 7090/91 as per below. Will start making the new COP work with the OEM ECU to begin with. --------------------- Time frame: Possibly installing the VEMS during winter 09/10 --------------------- ''' Questions ''' Q. Will it work with a Bosch Lambda 0 258 007 090, LSU 4.2 ? A.
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.