__        __
 \ \      / /
  \ \ /\ / / 
   \ V  V /  
    \_/\_/   
             

         
    ##   
         
    ##   
    ##   
    ##   
    ##   
 ####    

         
         
 ##  ##  
 ##  ##  
 ##  ##  
  #####  
    ##   
 ####    

 ##      
 ##      
 #####   
 ##  ##  
 ##  ##  
 ##  ##  
 #####   
         

         
         
 #####   
 ##  ##  
 ##      
 ##      
 ##      
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
= Audi urS4 1992 with the AAN engine = ||http://www.vems.hu/files/MembersPage/Magloman/audi-s4-1992.jpg||http://www.vems.hu/files/MembersPage/Magloman/aan_1.jpg|| ----- == My setup is for now: == * use all original sensors, except IAT that is changed to one from 1.8T (0 280 130 085): MembersPage/Magloman/IAT * replace the MAF with a MAP * WideBand Lambda Bosch LSU4.2 7090/91(7200) * make my own electrical loom/harness for the engine, using VAG OEM connectors and Econoseal connectors on the Vems. * Make the engine run nice and good. * make it work with COPs from 2005-2007 VAGs, 06B905115L, logic-level ** Guide for conversion from original POS/coil to COP here: ** http://www.bonnquattro.se/aan/18tCoilPackConversionInstructions.pdf ------- === What I know: === * I will buy the assembled vems with econoseal connectors * I need 5 logic outputs for the ignition ** I ordered 2+6 version * The extra flyback 30v diode seems like a good choice * I will buy a wideband lambda * I will buy a EGT sensor * I want the LED (4x20?) * I want a special lambda display * EGT and knock sensors(would like to use the stock knock sensors) * onboard MAP sensor 400 kpa * I will buy some econoseal connectors 18+36 * Primary trigger Is VR * Secondary trigger would be "audi trigger" * PS2 input for use with VSS ** I bought extra cable from Ps/2 to D-Sub with built in protection ------- === VEMS ECU info === * Board_version=v3.3 * Serial_nr= 2267 * pump-= 4.05V * wbo2_pump_pw_zero=0x64 (100) * wbo2_nernstdc_target=0x87 (135) * pump+= -1.0mV/200 Ohm * AREF=4.9V * (C103=1nF, no D100) ---- == Captains Log: == '''2016-06-19:''' * I have put together cable for the LCD and tested it out. https://youtu.be/nF_bM1gTyVo * I also fixed Bluetooth connection so I can connect to it in the car later on. * I also bought a cheap android pad and tested VEMSdisplay, very good! I like it alot! :-) '''2016-06-26:''' * Installed new Firmware v1.2.31 (had to update bootlaoder too using special cable) '''2017-01-24:''' * Still making electrical loom for the engine...It takes forever if you want it neat :-) But its kinda fun when you got it going and have all tools and stuff ready. * Some pictures of ongoing work: ||http://www.vems.hu/files/MembersPage/Magloman/aan_2.jpg ||http://www.vems.hu/files/MembersPage/Magloman/cop-connectors.jpg ||http://www.vems.hu/files/MembersPage/Magloman/crimpconnectors.jpg ||http://www.vems.hu/files/MembersPage/Magloman/injectorcables.jpg ||http://www.vems.hu/files/MembersPage/Magloman/spam.jpg ||http://www.vems.hu/files/MembersPage/Magloman/triggers.jpg '''2017-02-2:''' It is now running! :-) I had issues with correct amount of req fuel. Used formula and even got tips from other more experienced users of VEMS. I got lots of work todo now with other things; sensors and outputs. A little video of first succeeded run: https://youtu.be/NBqvxG8kXiI When WBO2 got power: https://youtu.be/rRiykK4U7pU ----- == VemsTune == * Using 2016 version * Ignition settings: ** Dwell 2.2ms (max 2.5 I think) ** MAP scale: 3
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.