____  
  / __ \ 
 | |  | |
 | |  | |
 | |__| |
  \___\_\
         
         

         
         
 ######  
 #  ##   
   ##    
  ##  #  
 ######  
         

 #       
 #       
 # ###   
 ##   #  
 #    #  
 #    #  
 #    #  
         

 #       
 #       
 #   #   
 #  #    
 # #     
 ## #    
 #   #   
         

 _____ 
(  _  )
| (_) |
|  _  |
| | | |
(_) (_)
       
       

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
Can't get my Genboard v2.2 working... Using Marcell's programming instructions from: http://www.x-dsl.hu/genboard/programmer.txt Currently my cable is wired as an STK200: <code> Header AVR(pin) LPT ------ --- --- 1 PDO(3) 10 2 VCC n/c 3 SCK(11) 6 4 PDI(2) 7 5 RESET(20) 9 6 Ground(2) 21-25 </code> AVRDude reports: ---- <code> C:\WinAVR>avrdude -c stk200 -p m128 -F avrdude: AVR device not responding avrdude: initialization failed, rc=-1 avrdude: AVR device initialized and ready to accept instructions Reading | ################################################## | 100% 0.00s avrdude: Device signature = 0xffffff avrdude: Yikes! Invalid device signature. Check stk200 entry in avrdude.conf and measure from end-to-end (parallel DSUB25 to AVR pin), and extend the table above with AVR pin number. (avrdude.conf looks the same as Marcell's instructions. <1Ohm from Dsub to AVR pins, everythings matches) avrdude: safemode: Fuses OK avrdude done. Thank you. C:\WinAVR> </code> ---- <code> this is what I use with linux mknod /dev/parport0 c 99 0 chmod a+rw /dev/parport0 avrdude -p t13 -c bsd -E noreset -e -U flash:w:test.hex AVR db25 reset to pin#7 SCK to pin#8 MOSI to pin#9 MISO to pin#10 gnd to pin#18 </code> ---- What I've checked: * Installed giveio.sys, service started * ISP pins to pins on AVR *** Had a bad solder on the VCC pin of the ISP header. Does this matter? * VCC/GND to AVR ** check all GND and VCC, there are many. Document your measurements here (include AVR pin number everywhere). *** AVCC (pin 64) - +5V *** VCC (pin 52) - +5V *** VCC (pin 21) - +5V *** < 1 Ohm from each ground pin to ground plane * Clock signal on XTAL pins ** what does it mean ? The clock is oscillating with 16 MHz ? *** Yes, didnt have a crystal, using a standalone oscillator feeding 16MHz TTL level pulses to XTAL1 What's next? I can scope it if necessary, just don't know what I'm looking for...
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.