#####  
 ##  ##  
 ##  ##  
  #####  
     ##  
     ##  

 ___   
(  _`\ 
| (_) )
|  _ <'
| (_) )
(____/'
       
       

 _   _ 
| \ | |
|  \| |
| . ` |
| |\  |
\_| \_/
       
       

 ###     
  ##     
  ##     
  #####  
  ##  ## 
  ##  ## 
 ######  
         

______ 
|  _  \
| | | |
| | | |
| |/ / 
|___/  
       
       

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
== Installing a VEMS unit on a stock 89 Porsche 911 Carrera 3,2. == ---- MembersPage/MacB/Config ''' <- please verify ''' MembersPage/MacB/Trigger MembersPage/MacB/Reports http://www.vems.hu/files/MembersPage/MacB ---- == Open Issues == ''' Help needed ''' * ''' Alternative trigger setting ''' can somebody ''' <- please verify ''' ** Number of cylinders = 6 ** Audi trigger divider = 43 ** TDC after the trigger = 60.0 ** Number of Teeth On Wheel = ''' 6 ''' ** # of teeth of full engine cycle = ''' 6 ''' ** First trigger tooth = 0 ** Next trigger tooth = 1 ** Angular Width of Tooth = 120 degrees ** Reference trigger tooth table = 0, 5, 4, 3, 2, 1 ** This looks much nicer in VEMSTune Trigger Settings Visual and engine runs with that, any downsides ??? *** masking the sectrig to only consider every second pulse ? * ''' injectors are grouped 1,2,3 and 4,5,6 ''' ** Req Fuel (Injector size) = 14.9ms (6,49 *(3164ccm/'''6'''/229,1ccm/min)) ** Injector firing Divider = ''' 3 ''' ** Number of primary injectors = ''' 2 ''' *** Seems to be wrong, way to much fuel ! * ''' Coil charge time @13,2V = 3,01ms ''' ** is this a good start value for a single BOSCH coil setup ? ---- '''Engine specs''' * 3,2litre flat-six '''normally aspirated''' ** number of cylinders=6 (even fire) * trigger system is '''2 VR sensors on flywheel / starter ring gear''' (crankwheel) ** rev sensor is sensing '''129teeth per crank rev''' *** 43*3, so divide-by-N N=43 *** the rest like ''reference tooth'' almost like with 3 teeth on the crank: a c003 trigger if sectrig comes just from 1 crankpulse, ( or c006 if camsync is also installed - which is not, at least initially ) ** TDC sensor is sensing 1 pin on flywheel (don´t know yet how many degrees before TDC). *** Will likely need to have (access to) a '''strobelight''' to verify all is well. * no cam or distributor sensor ** with auditrigger camHALLinverter the '''EC36/13 input must be grounded''' to allow the crankhome-VR pulse to go through. * stock NTCII at cylinder head #3 * AFM (flap type) will be removed, will use TPS instead (exchanging stock idle and WOT switch) * idle control valve is the "silver cigar" BOSCH thing, two wires to ECU, so PWM * '''IGN distribution''' will remain untouched in first step, stock coil, stock distributor * stock fuel injector BOSCH 0-280-150-158 low-Z (2-3 Ohms) ** '''order with "low-Z extension" option''' if you keep the high-Z injectors (and configure PWM-ing: ~35% PWM duty after 1msec full-voltage) * wideband O2-sensor will be used intead of stock narrowband * no MAP. ** It would be easier to tune with a MAP sensor, but also possible with TPS, with more work * MAT now planed ** The '''MAT sensor is almost a MUST''' (in a normally aspirated engine MAT sensor can be an NTC in the air-filter, very simple and cheap, just make sure the engine will never inhale it) * '''Firing order is 1-6-2-4-3-5''' for the Carrera * wiring should remain mainly stock with stock-DME-connector and only additional wires for wideband, TPS and so on * planning to use alpha-N only ---- '''VEMS-spec: / Needed parts''' * VEMS Board version v3.6 ** Serial nr.= 8234 ** (Order ID= 8044) ** Flyback: LowZ active flyback 8ch ** ignition driver: 8 ** primary_trigger: EC36/27 VR ** secondary_trigger: auditrigger w/camHALLinverter ** Knock input channels: 0 ** LCD connection: no ** MAP connection: offboard(electronic) ** mounting-style: no-screws ** 1-wire interface: no ** EGT input: no ** PS2 connection: no ** withSDcard: no * Other stuff: ** DME-plate with 35-pin-connector DIY ** TPS from E36 (Hella): 6PX 008 476-111 *** Adapter plate DIY ** WBO2 (Bosch): 0 258 007 351 ** MAT (Bosch): 0 280 130 039 *** intake pipe DIY ** 1 x Wideband connector ** 1 x Econoseal18-Wire side ** 1 x EconoSeal36-Wire side ** Some other connectors etc. ---- ---- ''' Related projects by other users: ''' Looks like a similar setup: MembersPage/KevinBlack/PorscheTurbo
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.