### ### ### ## ## ## ## ####
_________ \__ _/ ) ( | | | | | | |\_) ) (____/
___ ( _`\ | (_) ) | _ <' | (_) ) (____/'
#### ## ## ## ####
____ / __ \ | | | | | | | | | |__| | \____/
IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now. Visit Preferences to set your user name Summary of change: Engine: Lancia Thema 2,0 16V Turbo (834 C 1.000) - Displacement: 1995ccm - Bore: 84mm - Stroke: 90mm - Cilinders: 4 in line - Firing order: 1-3-4-2 - Distribution: by belt, DOHC (2 cams in head) - Rotation: right Engine tuned parts: - Turbocharger: Garrett GT3076R, (internal wastegate), assumed pressure: little more than 2 bar - Throttle butterfly: Jaguar 4,0L, Diameter: 73mm - Exhaust manifold: tubular type, diameter of each pipe: 42mm - Intercooler: Water to Air type Engine sensors (which will be used in my project): Crankshaft (Trigger 1): -'''pulley(Crank): 60 teeth -2''' -sensor type: '''VR''' (Magneti Marelli SEN 8D - '''700 Ohm''') from Lancia Delta/Escort RS '''Camshaft (Trigger 2)''': * Option 1: ** pulley: 1 tooth ** sensor type: VR (Magneti Marelli SEN 8D – 700 Ohm) from Lancia Delta/Escort RS ** low toothcount VR sensors are more sensitive to signal conditioning (pullup, pulldown) and noise * Option 2: ** pulley: 1 tooth ** sensor type: '''HALL''' ( Bosch 0 232 103 039) from Fiat Punto,Doblo,... ** if you have the option, HALL sensor is a better choice than VR ..............(OK, i will use HALL sensor for Trigger2) Throttle position sensor (TPS): -type: Bosch 0 280 122 001 -total resistance : cca 2 kOhm -number of wires: 3 Water temperature sensor (WT): -type: negative temperature NTC (appr. 2252 Ohm at 25C) -mark: Bosch 0 280 130 026 -impedance at -10°C = 9 kOhm -impedance at +20°C : 2,5 kOhm -impedance at +80°C : 0,3 kOhm -voltage: 5V -number of wires: 2 Intake Air Temperature sensor (IAT): -type: negative temperature NTC (appr. 2252 Ohm at 25C) -mark: Bosch 0 280 130 060 ( from Lancia Kappa 2,0 16V Turbo) -impedance at -10°C = 9 kOhm -impedance at +20°C : 2,5 kOhm -impedance at +80°C : 0,3 kOhm -number of wires: 2 Manifold Absolute Pressure sensor (MAP): -VEMS external MAP sensor -Max. pressure: 400 kpa -Voltage: 12V Knock sensor: Option 1: -mark: Magneti Marelli SEN 14B -operation frequecy: 12-16 kHz Option 2: -mark: Bosch 0 261 231 006 (usualy used by VEMS) .........'''Which knock sensor will be better? I preffered Marelli, because it is stock sensor used by Lancia...but if i cant use it for Vems, i can change it with Bosch one.''' Lambda sensor (O2): -type: Wideband (5V) -mark: Bosch 0 258 007 351 (recommended by Vems) -number of wires: 6 Exhaust Gas Temperature sensor (EGT): * type: VEMS * diameter: 2mm * without amplifier. VEMS ECU (if chosen with 1 or 2 EGT inputs) does NOT need external amplifier. For VEMS v3, external amplifier only needed for more than 2 EGT inputs. Other (non-VEMS) ECU-s that lack K-thermocouple inputs (but have 0-5V or 0-10V input) need external amplifier for K-thermocouples ..........I will use only 1 EGT sensor (input) so i am happy, that i dont need amplifier :) Engine actuators (which will be used): Ignition: -wasted spark type with 2 coils -Coils type: Marelli BAE 800B (060708038010) -Primary coil resistance: 0,54 Ohm -Secondary coil resistance: 7500 Ohm -Spark plugs: NGK BP6ET (3 electrodes in circle) Injection: -Injectors type: Peak & Hold -Number of injectors: 4 -Resistance of 1 injector: '''2,5 Ohm''' @ 68F -Injectors mark: RC Engineering, 750 cc/min @ 43,5 PSI -Injectors drivers: one driver per one cilinder -'''Additional series resistor for injectors''': OEM type, cca '''7 Ohm''' per each inj. (for higher flowrate, eg. 1200-2400cc low-Z injectors, the [http://shop.vems.hu/catalog/lowz-extension-channel-p-160.html low-Z extension 4channel] would be better, but at 750cc/min (where idle pulsewidth not extremely short) the gains are negligible compared to the simpler series-resistors ........'''So, if i understand it right, if i order ECU with lowZ-4channel, i cant use additional series resistors for injectors and i can plug injectors directly to ECU?''' -Fuel pump: Bosch 0 580 254 044 -Fuel pressure: 3-5 bar Boost Control Valve: -for this time unconnected...after: OEM Solenoid Bosch or Pierburg Display: - VEMS LCD Display (green) http://www.vems.hu/files/LanciaSlovakia/Wiring%20diagram%20%28VEMS%29%20Tomas%20Polonec%20Fiat%20127%20Lancia%20engine.jpg ---- Note from support crew: You've made '''good plans, and a nice description of your project''', include the page URL in your order comment and negotiate some '''discount''' for v3. ---- Thank you support crew ;) But before i order my V3, i have some questions...i send an e-mail to info@vems.hu and waiting for answer. Here is my project car, which actualy runs with stock ECU and it is tuned for 290HP and 400 Nm. I hope with VEMS it will be better :) This is actualy result without Vems: http://www.vems.hu/files/LanciaSlovakia/Fiat%20127%20Luigi.jpg Optional: Add document to category: Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.