##  
     ##  
  #####  
 ##  ##  
 ##  ##  
  #####  
         

         
         
  #####  
 ##  ##  
 ##  ##  
  #####  
     ##  
 #####   

         
         
  ####   
 ##      
 ##      
 ##      
  ####   
         

   ___ 
  |_  |
    | |
    | |
/\__/ /
\____/ 
       
       

     ### 
  #####  
 ##  ##  
 ##  ##  
 ##  ##  
 ##  ##  
  ### ## 
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
'''TRACTION CONTROL STRATEGY''' ------------------------------------- Car Audi a8 quattro 2.2 20VT 950hp Vems 3.6 I need some strategy for a traction control when car starting some spark cut or slow reving by a specific time , or ignition retard for first gear, im need some specjal solution A: It is possible to use per gear boost target, per gear ignition trim, anytrim (http://vems.hu/vt/help/v3/v3_anytrim_control.html) on slip ratio between front/rear wheels or launch time. '''Any or a combination of these functions should provide proper off starting line response''' - DB --------------------------------------------------- How I can reduce power on start only ?? in all of this option car always running on retard ignition on 1 or 2 gear or reduced boost or when im active launch time vs ignition retard i have retard ignition on each gear. Im need some special conditions for launch setup some like no2 conditions , and strategy for holding rpm by specified time 0,1 sec on 4100 rpm 0,2 sec on 4300 rpm 0,3 sec on 4500 rpm 0,4 sec on 4900 rpm etc... In wheelspeed firmware '''by-speed launch-RPM limit is more reasonable''' and more commonly applied. Using by time is also possible: * definitely in the PS2 firmware. * I think even in wheelspeed firmware, anyttrim on launchtime (+ 50% tps) and trim launch rpm easy * see: http://vems.hu/vt/help/v3/v3_anytrim_control.html for more details '''Trigger Problem With hall sensor''' ------------------------------------- i use this sensor and trigger wheel sensor: https://www.autoatu.ro/uploads/tdimages/159/01590175803255.jpg trigger wheel http://autodbase.ru/433_2016_2q_deadlock38/images/162/01620265803255.jpg and problem is with trigger errors i change in vems SJ2 closed, SJ6 open R30 pullup - install 4k7 resistor, and 2701 still problem my config file http://www.vems.hu/files/Audi%20URS4%20Kryinu/v3.3_u006060-2017.07.18-08.33.21%20do%20wysylki.vemscfg trigger log 4k7 resistor http://www.vems.hu/files/Audi%20URS4%20Kryinu/v3.3_u006060-2017-07-17-18.19.28%20with4k7%20resistor.triggerlog trigger log 2701 resistor http://www.vems.hu/files/Audi%20URS4%20Kryinu/v3.3_u006060-2017-07-17-15.22.20%20with%202701%20resistor%20.triggerlog photo inside ecu before SJ2 closed, SJ6 open http://www.vems.hu/files/Audi%20URS4%20Kryinu/19876028_1498476506888955_180108406_o.jpg http://www.vems.hu/files/Audi%20URS4%20Kryinu/19897854_1498475240222415_378634031_o.jpg http://www.vems.hu/files/Audi%20URS4%20Kryinu/20049082_1498475283555744_585077620_o.jpg http://www.vems.hu/files/Audi%20URS4%20Kryinu/20049142_1498476986888907_1963152840_o.jpg ----- Hello, Thanks for your elaborate report, this helps pinpointing the source quickly. Your tirggerlog(s) shows inverted polarity on the primary trigger sensor and your config confirms; please change primary trigger edge to '''FALLING''' from rising and power cycle the ecu. If you are still having issues after that, please upload a new triggerlog and vemslog (or vemscfg) so i can review. Best regards, Dave ----- Car running sometimes but i must 4 or 5 times cranking trigger log when is trigger error http://www.vems.hu/files/Audi%20URS4%20Kryinu/v3.3_u006060-2017-07-18-12.09.41.triggerlog log when trigger error http://www.vems.hu/files/Audi%20URS4%20Kryinu/v3.3_u006060-2017.07.18-12.10.25%20do%20wysylki.vemslog config actual http://www.vems.hu/files/Audi%20URS4%20Kryinu/v3.3_u006060-A-2017.07.18-12.10.50%20do%20wysylki%202.vemscfg when car start work fine log and trigger log http://www.vems.hu/files/Audi%20URS4%20Kryinu/v3.3_u006060-2017.07.18-12.22.16%20when%20running%20ok.vemslog http://www.vems.hu/files/Audi%20URS4%20Kryinu/v3.3_u006060-2017-07-18-12.20.10%20when%20running%20ok.triggerlog ----- I have reviewed your vemslogs and triggerlogs, your errors are caused by secondary trigger settings, please disable "ignore sectrig pulses above" set to 255 instead of current 0. Also config validation shows many warnings and errors please correct those before anything else. Judging from your triggerlog "v3.3_u006060-2017-07-18-12.09.41.triggerlog", tcd delay is not configured correctly, '''make sure to verify and recalibrate both trigger tooth and tdc delay before all else with timing light''' Best regards, Dave ------ '''when i change ignore sectrig pulses above to 255 everything works great thanks alot ''' '''ANALOG IN PROBLEM''' ------------------------------------- all chanels 0v I change mcp3208 but still nothing i use this http://www.tme.eu/pl/details/mcp3208-bi_sl/przetworniki-ad-uklady-scalone/microchip-technology/ http://www.vems.hu/files/Audi%20URS4%20Kryinu/IMG_20170731_140326.jpg http://www.vems.hu/files/Audi%20URS4%20Kryinu/IMG_20170731_140250.jpg problem solved i change vems tune to older from 2016 06 06 and everything works fine
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.