##    
         
  ###    
   ##    
   ##    
  ####   
         

    ##   
         
    ##   
    ##   
    ##   
    ##   
    ##   
  ###    

  ____  
 |  _ \ 
 | |_) |
 |  _ < 
 |_| \_\
        

         
   ##    
 ######  
   ##    
   ##    
   ##    
    ###  
         

         
         
 ######  
  ##  ## 
  ##  ## 
  #####  
  ##     
 ####    

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
Want to do a PnP install on my Mazda 323 GT-R but also on some Group H Rallye Cars. Hardware is 90% done. Sotware is 20% done. == Questions: == Q. TDC is 84° after rising edge of primary trigger. Ignition advance gets up to 55°. Now Coil charge time gets down to about 1,5ms on 6500rpm but i want at least 3ms. Is there a way to start charging before the rising edge? Q. Does anybody has working Tables on this engine? Because my Genboard does exactly the same as factory ECU but the engine doesn't run good. Q. Is there a way to change the starting point of fuel injection? == Specs: == ==== Engine: ==== *4cyl *1800ccm *440cc Injecotors ==== Ignition: ==== *Single Coil + Distributor *Ignition Module (using Logic-Level Output) ==== Trigger: ==== *4+1 Cam Sensor ==== Sensors: ==== *Flap type AFM *TPS ==== EMS: ==== *Genboard 3.5 *Firmware 1.1.50 (downgrading to 1.1.27 until engine runs perfect) == Progress: == ==== Hardware: ==== *Genboard installed in factory ECU case *installed additional 9pin connector for IAT, MAP and WBO2 *MAP/AFM, IAT and NBO2/WBO2 swichtable *WBO2 and MAP sensor have been already installed in car for a ZEITRONIX WBO2 Display *built a trigger emulator with mega8 uC for testing ===== TODO: ===== *install EGT *check if factory knock can be used with vems *intall wasted spark ignition coil ==== Software: ==== *Measured Trigger with Scopemeter *Measured ignition timing of factory ECU *Measured injector pulse witdh of factory ecu *Engine starts and runs but very badly ===== TODO: ===== *Get engine running stable with AFM *Get engine running with MAP sensor *Values for warmup and acceleration enrichment doesen't work good *Get WBO2 working *Get wasted spark ignition working *Boost control when using MAP Sensor *ALS/Launch Control == Information: == ==== Trigger: ==== Same Trigger as on [MembersPage/Fero] but i measured angles with scopemeter and got this values: http://www.vems.hu/files/MembersPage/Kottan/Trigger2.JPG ==== Ignition: ==== Factory ECU has no ignition table. timing is calculated of rpm and AFM voltage. Tested up to 30000rpm. http://www.vems.hu/files/MembersPage/Kottan/Spark1.JPG ==== Fuel: ==== factory fuel table measured with scopemeter: http://www.vems.hu/files/MembersPage/Kottan/Fuel1.JPG
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.