_______ ( ____ ) | ( )| | (____)| | __) | (\ ( | ) \ \__ |/ \__/
_____ |_ _| | | | | _| |_ \___/
_ ( \ | ( | | | | | | | (____/\ (_______/
##### ## ## ## ## ##### ## ##
_____ |_ _| | | | | | | \_/
IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now. Visit Preferences to set your user name Summary of change: Greetings from Finland! ---- My project car is Ford Escort Mk4 -87 Plans to season 2011: Install VEMS and throttle bodies On July 2010 I got it to the dragstrip and results are: ET 14,32 s and speed 158,73 km/h On August 2010 we got it to the dyno and results are: 129,9 Kw and 231,3 Nm. http://i200.photobucket.com/albums/aa215/koskar1/RS2K/Mk4%20RS2000/mk4_rs2k.jpg Engine: - Ford Galaxy -99 2.3i 16V engine block and cylinder head - Ford Escort RS2000 -92 cams, exhaust header and intake manifold - Ford Escort Cosworth T25 fuel pressure regulator (3,5bar) - Davies Craig electric water pump and controller - Ford Escort RS2000 ECU (EEC-IV) with Collins chip and EDIS4 with dual coils http://i200.photobucket.com/albums/aa215/koskar1/RS2K/Mk4%20RS2000/botnia2010_4.jpg ---- '''My VEMS history :)''' I build one VEMS project in 2008, but I sold it forward because I didn't have time to tune it. So it's time to try again! Old wiring harness and ECU: http://i200.photobucket.com/albums/aa215/koskar1/RS2K/VEMS/tags.jpg ---- '''VEMS external hardware''' Injectors: Bosch 0 280 155 504 (~280cc/min@3,5bar?) Coils: Ford dual coils Coolant sensor: maybe GM because resistance range is suitable and it's got correct thread Intake air sensor: GM for same reason Primary trigger: Ford VR sensor Secondary trigger: Ford VR sensor, reading exhaust cam at cylinder 4 (I'm not sure do I use this at the beginning at all) TPS: Keihin TPS (stock Suzuki GSXR1000 K2) LCD: 20x4 black/green with inverted colors Lambda: Bosch 057 ---- '''VEMS related shopping list''' Soon I will make order to VEMS shop and I have allready collected some VEMS related items to my project (LCD, knock sensor and wiring harness stuff). --> Done Products 1 x GenBoard v3.6 - Ship start: 2 weeks 247.30EUR 1 x Alubos1600 - Drill-count: 6 27.04EUR 1 x Alubos EC frontplate - Drill-count: 0 15.97EUR 1 x Alubos Endplate - Drill-count: 4 5.84EUR 2 x Alubos gasket 4.14EUR 3 x clamping plate 7.89EUR 1 x Additional VR or Coil interface 3.99EUR 1 x Econoseal18-PCB 9.87EUR 1 x Econoseal36-PCB 13.89EUR 1 x Econoseal18-Wire side 9.90EUR 1 x EconoSeal36-Wire side 16.70EUR 1 x Wideband connector - With wire: without wires 5.60EUR 1 x Idle stepper motor driver 3.00EUR 4 x Ignition driver 14.64EUR 1 x Ignition driver insulator sheet - Size: 3lines 1.90EUR 9 x Injector or WBO2 heater driver 17.10EUR 1 x PTC fuse 0.71EUR 1 x Throughole Diode - Model: 30V flyback 0.38EUR 1 x Throughole Diode - Model: 18V unidir 0.43EUR 2 x VEMS sticker - Color: white 0.56EUR 2 x VEMS sticker - Color: red 0.74EUR 1 x VEMS sticker - Color: metallic: silver 0.45EUR Total: 412.94EUR ---- '''Questions and answers''' '''1.''' I want to be sure with primary trigger config. So, when using 100% same '''36-1''' triggering that Ford EDIS use, what are correct settings? * use the 4cyl 36-1 configlet (we make sure it's available nov 12) ** toothwidth=10 degrees ** next trigger tooth: 18 ** reftooth 0,18,0,18 ** EDIS4 = missing tooth is 90 degrees before VR sensor when first cylinder is in TDC. Trigger wheel is solid mounted to crankshaft and VR sensor is solid mounted to block. Is it same as in this page http://www.vems.hu/wiki/index.php?page=InputTrigger%2FMultitoothTriggerWheel ? (TDC before trigger ~ 83 degrees)- note that TDC should be measured after tooth0 which comes after the long gap. Preferrably also strobed. # TDC of cyl1 (and cyl4) comes # 83 degrees after the point, when # the first tooth after the missing tooth just passes the trigger (considering the rotational direction). # that is 8 tooth and a little on the 36-1 wheel. # we place trigger_tooth to 20 degrees (02 teeth) # so 63 degrees remains for ign_tdcdelay # so the sum is 83 degrees Yes, the above is the recommended for 1.0.x firmware. Also works on 1.1.x, but often triggertooth=0 and TDC after trigger=83 is used on 1.1.x instead. (makes little difference, maybe in the position of staging injection injstart). '''2.''' What best suitable firmware to my project? Just put latest version and that's it? 4cyl, 36-1 VR trigger, n/a ITB, wasted spark latest (eg. 1.1.84) should be reasonable to try. Optional: Add document to category: Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.