|\     /|
| )   ( |
| |   | |
| |   | |
| |   | |
| (___) |
(_______)
         

         
         
 ######  
    ##   
   ##    
  ##     
 ######  
         

         
         
 ##  ##  
 ##  ##  
 ######  
 ######  
 ##  ##  
         

 ___   
(  _`\ 
| | ) |
| | | )
| |_) |
(____/'
       
       

         
         
  ####   
 ##  ##  
 ##  ##  
 ##  ##  
  ####   
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
'''VW MK3 GTI VR6 Project''' || [http://www.vems.hu/wiki/index.php?page=MembersPage%2FKevinBlack%2FVWMKIIIGTIVREngine Engine]|| [http://www.vems.hu/wiki/index.php?page=MembersPage%2FKevinBlack%2FVWMKIIIGTIVROrder ECU Order]|| [http://www.vems.hu/wiki/index.php?page=MembersPage%2FKevinBlack%2FVWMKIIIGTIVRWiring Wiring]|| [http://www.vems.hu/wiki/index.php?page=MembersPage%2FKevinBlack%2FVWMKIIIGTIVRDynos Dynos]|| [http://www.vems.hu/wiki/index.php?page=MembersPage%2FKevinBlack%2FVWMKIIIGTIVRNews News]|| ---- Originally built and tuned with DTA engine management. Driveability/idle problems cause owner to look elsewhere. V3 ecu installed using same wiring/AEM Injector Driver/RC Low-Z 1000cc injectors. Currently street/dyno tunes and running. Car ran 7.16@104.98 MPH 1/8th mile drag. ---- '''AEM Injector Driver Specs''' AEM PEAK & HOLD INJECTOR DRIVER AEM PN 30-2710 EM’s external Peak & Hold Injector Driver module allows ECU’s that have a saturated injector drive circuit to trigger low impedance injectors with a true 4/1 Peak & Hold injector drive circuit. AEM’s Peak & Hold Injector Driver contains 10 independent injector drive channels. Each channel supplies full battery voltage to a fuel injector for rapid current rise, in order to produce positive injector opening. When load current reaches 4.1A (amps), the injector driver reduces the load current to 1.1A and operates as a constant current source. This condition holds the injector open, and reduces system power dissipation. If the current fails to reach 4.1A within 5mS, the driver module automatically reduces the load current to 1.1A. For high-output racing engines that have exceeded the capacity of high-impedance injectors Includes 10 independent injector drive channels for any engine up to V10 Complete wiring system included Operating Voltage: 8-18 volts, negative ground RPM Capability: Unlimited Injector Triggers: 10 Trigger Waveform: Output is activated when input trigger is grounded Trigger Impedance: 220 Ohm input impedance, pulled to 12V (60 mA draw) Injector Outputs: 10 Output Current High: 4.15A Peak, Typical Output Current Low: 1.15A Sustain, Typical Peak Current Timeout: 5mS Size: 5.5"L x 4.6"W x 1.4"H Weight: 2.7 Lbs Over Temperature Shutdown: 115C (Nominal) ----
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.