###      
 #####   
 ##  ##  
 ##  ##  
 ##  ##  
 ##  ##  
######   
         

         
         
 #####   
 ##  ##  
 ##      
 ##      
 ##      
         

         
 ##      
 ##      
 #####   
 ##  ##  
 ##  ##  
 ##  ##  
         

 _____ 
|  _  |
| | | |
| | | |
\ \_/ /
 \___/ 
       
       

  _  __
 | |/ /
 | ' / 
 |  <  
 | . \ 
 |_|\_\
       
       

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
Porsche 911 Turbo '''6 cylinder engine''', engine unknown but had the Motronic from the 3.2 engine running before vems install. The engine is similar to MembersPage/MacB ---- '''Update: the car is running on 1.1.98 fw. Good job guys!''' For the c129 signal, '''divby43, 1.1.98 (17-Jan-2012 or newer) firmware needed''' from [http://cell.dyndns.ws/f/ developer testserver] * See the http://cell.dyndns.ws/f/README.txt how to install this * (1.1.98 not released to the public yet, but actually seems better than anything before). * With the 129 tooth, we tested beyond 10000 RPM (on the bench, including ignition and injection outputs). * The change we did was basically a revert of change that was made to a certain request, but not extensively tested yet ** basically auditrigger behaviour should be now as good as back in 1.1.95 for non-3 divider also ** but with the desired changes - eg. allowing all 3 trigger signals to be connected and scoped independently with v3. ---- * '''injector outputs: only injgroup 0, 4 and 5''' were used (this might seem unconventional, it's all because the sectrig is not 720 deg but 360 deg), ** so we enabled '''2 inj outputs''' (we paired the outputs that are actually 360 deg opposite) in injgroups 0,4 and 5 (and '''left injgroup 1,2,3 empty'''). *** '''Why not use injgroups 0,1,2, and also set "Number of primary injectors" to "3" instead of "6"?''' ****'''also, should "two stroke" or "four stroke" be used in this setting?(latest config is set to two stroke)''' ---- Trigger setup: Flywheel tooth and flywheel pin triggering, flywheel is 129+1. ---- ECU Info: ECU#4215 vr/vr trigger(auditrigger non camhall) Tlywheel Tooth Trigger to EC36-27 Flywheel Pin Trigger to EC18-12 ---- Here's link to 911 Workshop Manual, years 1984-1989: http://www.cannell.co.uk/911_72-89_Workshop_Manuals/84-89%20Workshop%20Manual.pdf Maybe there's some info on 911 Turbo as well.(MembersPage/PeepPaadam) ---- * '''[http://cell.dyndns.ws/f/v3_firmware_1.1.98.zip 1.1.98 (experimental)] was tested, and found good with this divby 43 config''' ** http://www.vems.hu/files/KevinBlack/porsche-1.1.98-divby43.zip with config, vemslog, triggerlog ** note: anything after "auditrigger with third trigger input software "camHALL scope" (2011-08-02) will NOT work, so '''1.1.96 and 1.1.97 will NOT work''' (at all with this trigger, see GenBoard/UnderDevelopment/FirmwareChanges ). 1.1.95 should work (we didn't tested it) * Trigger Edge: Rising * Trigger Type: Coil Type * Special Trigger Type: Auditrigger DivbyN * Audi trigger '''divider: 43''' * Number Of Teeth On Wheel: 3 (NOT 6, because only 3 per sectrig. 3*120=360 as sectrig pulse comes every 360 deg on this engine) * First Trigger Tooth: 0 * Next Trigger Tooth: 1 * Angular Width Of Tooth: 120 * Filtering and below: Disabled * reftooth: 0 2 1 0 2 1 x x (because teeth 3,4,5 does NOT exist) Secondary Trigger: * Mode: Cam Sync * Edge: Rising * Edge While Cranking: Single * Use: Cam Sync ---- We also tested with no divider (tooth width=2.75 deg): it worked, but peak-RPM would likely be limited. '''This special case of auditrigger worked on bench''', including the per-cyl delay, but '''only after tricking''' "divider-off, than "divider-on" (so we're working on initialization change, needed so it syncronizes without this trick, currently stuck in tooth_cnt=FF and wouldn't spark without this hack). Likely this will be the recommended setup). Per-cyl ignition delay is needed (because 43/3 != 14) * divby3 * toooth width=8.5 * Number Of Teeth On Wheel: 43 * First Trigger Tooth: 0 * Next Trigger Tooth: 14 * Angular Width Of Tooth: 8.5 * Filtering and below: Disabled * reftooth: 0 28 14 0 28 14 x x (because teeth 3,4,5 does NOT exist) * '''per-cyl ign delay: sg. like 0 5.5 2.75 0 5.5 2.75 0 0''' degrees ** needs verification with strobelight + adjustment if necessary * '''injector outputs: only injgroup 0, 4 and 5''' were used (this might seem unconventional, it's all because the sectrig is not 720 deg but 360 deg), ** so we enabled '''2 inj outputs''' (we paired the outputs that are actually 360 deg opposite) in injgroups 0,4 and 5 (and '''left injgroup 1,2,3 empty'''). ***'''see question at the top of page'''
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.