#### ### ## # ## # ## # ### ##
_____ |_ _| | | | | | | \_/
## ### ## ## ## ####
### # #### # # ### #
## ## ## ## ## ## ###
IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now. Visit Preferences to set your user name Summary of change: Porsche 911 Turbo '''6 cylinder engine''', engine unknown but had the Motronic from the 3.2 engine running before vems install. The engine is similar to MembersPage/MacB ---- '''Update: Sec trigger enabled, now there is primary and sec trig in triggerlog, but No RPM or Spark.''' Triggerlog: http://www.vems.hu/files/KevinBlack/Triggerlog%20No%20Spark.jpg VemsLog: http://www.vems.hu/files/KevinBlack/No%20RPM%20Log%20v3.3_u004215-2011.12.24-17.55.46.vemslog You have no 6 virtual teeth between "cam" signal [in similarity as we have for audi where every second TDC signal is cancelled by Hall]. So try with 3. may be 1.1.97 work with no divider? GintsK ---- Trigger setup: Flywheel tooth and flywheel pin triggering, flywheel is 129+1. ---- ECU Info: ECU#4215 vr/vr trigger(auditrigger non camhall) Tlywheel Tooth Trigger to EC36-27 Flywheel Pin Trigger to EC18-12 ---- Here's link to 911 Workshop Manual, years 1984-1989: http://www.cannell.co.uk/911_72-89_Workshop_Manuals/84-89%20Workshop%20Manual.pdf Maybe there's some info on 911 Turbo as well.(MembersPage/PeepPaadam) ---- The engine actually ran for about 45 seconds (without sectrig enabled), it was just luck that it happened to fire correctly on that attempt. * Trigger Edge: Rising * Trigger Type: Coil Type * Special Trigger Type: Auditrigger DivbyN * Audi trigger '''divider: 43''' ** yes, this '''seems like a valid config, but it didn't seem to work anyway''' (at least with 1.1.97), we're investigating it further ** (Per-cylinder ignition delay is not needed with it). * Number Of Teeth On Wheel: 3 (NOT 6, because only 3 per sectrig. 3*120=360 as sectrig pulse comes every 360 deg on this engine) * First Trigger Tooth: 0 * Next Trigger Tooth: 1 * Angular Width Of Tooth: 120 * Filtering and below: Disabled * reftooth: 0 2 1 0 2 1 x x (because teeth 3,4,5 does NOT exist) Secondary Trigger: * Mode: Cam Sync * Edge: Rising * Edge While Cranking: Single * Use: Cam Sync ---- We also tested with no divider (tooth width=2.75 deg): it worked, but peak-RPM would likely be limited. We also '''tested with divby3''', emil or pacsa will upload config and link here. '''This special case of auditrigger worked on bench''', including the per-cyl delay, but '''only after tricking''' "divier-off, than "divider-on" (so we're working on initialization change, needed so it syncronizes without this trick, currently stuck in tooth_cnt=FF and wouldn't spark without this hack). Likely this will be the recommended setup). Per-cyl ignition delay is needed (because 43/3 != 14) * divby3 * toooth width=8.5 * Number Of Teeth On Wheel: 43 * First Trigger Tooth: 0 * Next Trigger Tooth: 14 * Angular Width Of Tooth: 8.5 * Filtering and below: Disabled * reftooth: 0 28 14 0 28 14 x x (because teeth 3,4,5 does NOT exist) * '''per-cyl ign delay: sg. like 0 5.5 2.75 0 5.5 2.75 0 0''' degrees ** needs verification with strobelight + adjustment if necessary * '''injector outputs: only injgroup 0, 4 and 5''' were used (this might seem unconventional, it's all because the sectrig is not 720 deg but 360 deg), ** so we enabled '''2 inj outputs''' (we paired the outputs that are actually 360 deg opposite) in injgroups 0,4 and 5 (and '''left injgroup 1,2,3 empty'''). Optional: Add document to category: Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.