Editing MembersPage/KevinBlack/Audi

      #  
      #  
  ### #  
 #   ##  
 #    #  
 #   ##  
  ### #

 _______ 
(  ____ )
| (    )|
| (____)|
|  _____)
| (      
| )      
|/

    ##   
         
   ###   
    ##   
    ##   
    ##   
 ## ##   
  ###

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.

Visit Preferences to set your user name
Summary of change:
Update: Project is active with a new customer. ---- 1991 Audi 200 20v turbo,(3B) * Developers actually have a 3B test engine (that is 20VT engine with 3B harness) for testing several stuff: MembersPage/MarcellGal/PowerAndTraction ---- '''VEMS Motronic Audi 3B ECU Configuration''' MAP connection 400kPa onboard - brass nipple Flyback - 30v Diode LCD - Connector through endplate (DSUB9 with flying loom) EGT - Flying Loom through endplate Knock - Via Motronic55 Pins IAT - Audi PTC Sensor (430 Ohm pull-up) ---- '''Custom Pinout Information''' '''Ignition Setup - Flying Lead''' * 5 individual High Power coils (034) * Flying lead 5 wires (~150mm) for high power ignition outputs * I will supply the connector * 1 logic level connected internally to OEM IGN as backup. ---- '''WB02 - Flying Lead''' * black Nernst,WBO2 Pin 1 * thick brown-red wire from +12V flyback (motronic pin37) * thick brown Heater(-),WBO2 Pin 4 * transparent Pump(-),WBO2 Pin 5 * thin red Pump(+),WBO2 Pin 6 ---- '''Extra Analog Inputs - TBD''' ---- ---- '''General Audi Information''' Pic of ECU Connector: http://www.vems.hu/files/Audi%203B%20Connector/ECUconnector.jpg 3B Wiring Pinout: http://www.s2central.net/motronic_pinout_3B.html 3B Wiring Schematic: http://www.s2central.net/images/3B_ECU_Schematic.jpg Audi 3B Information: http://www.s2central.net/motronic_02.html http://www.sjmautotechnik.com/trouble_shooting/20vboost.html ---- '''For 3B, specify choice for the extra SSC6 connector''' MembersPage/TeppoKalske page bottom has the standards for SSC6 female pinout: * either "3B ECU extra connector pins" * or "AAN ECU extra connector pins" Or "your custom pinout you like, eg. 4 outputs and 1 analog input" and 1 GND. As you see, the "AAN ECU extra connector pins" has 3 analog inputs, we use one brake-light switch mounted under clutch (and a series switch that can disable it) to pull down (activate) the (shared) input for shiftcut and launch. When activated with TPS < iac_tps_threshold launch is activated (TPS can be pressed after activation). Otherwise shiftcut is activated. In any case, one must specify his extra-connector pinout preference for a 3B engine. ---- ---- '''OLD SETUP USED FOR REFERENCE - DO NOT USE''' '''IGNITION out and analog inputs''' Motronic55, Pin 1 is Stepper D, EC18 Pin 11 Flying Lead (No connector, I will supply) * black Stepper A, EC18 Pin 4 (EC10/1) * green Stepper B, EC18 Pin 10 (EC10/2) * orange Stepper C, EC18 Pin 5 (EC10/3) * thick lightblue EC36 Pin 11 (Logic level) (EC10/10) * vivid-blue mcp3208ch7 analog input with 2k7 pullup (EC10/7) * transparent mcp3208ch6 analog input with 2k7 pullup (EC10/6) * pale-blue mcp3208ch5 analog input (EC10/5) ---- '''analog input usage: Launch Control / WOT Shift Cut''' Flying Lead (No connector, I will supply) * Analog Input for: "Brake-light switch mounted under clutch (and a series switch that can disable it) to pull down (activate) the (shared) input for Shift Cut and Launch. ** When activated with TPS < iac_tps_threshold launch is activated (TPS can be pressed after activation). Otherwise Shift Cut is activated." '''Possible extra feature:''' - Air Conditioning / Radiator Fan "Idle-Up" Input
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.