_____ 
(___  )
    | |
 _  | |
( )_| |
`\___/'
       
       

   ##    
   ##    
  #####  
   ##    
   ##    
   ## ## 
    ###  
         

 _____ 
/  ___|
\ `--. 
 `--. \
/\__/ /
\____/ 
       
       

         
|\     /|
| )   ( |
| |   | |
( (   ) )
 \ \_/ / 
  \   /  
   \_/   
         

     ##  
         
    ###  
     ##  
     ##  
 ##  ##  
 ##  ##  
  ####   

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
== Project Summary == My name is Ken Lanham from Denver, Colorado in the United States. My project is a Volvo 740 Wagon with a turbocharged 16v engine. VEMS is replacing an aging megasquirt system to help push the power level higher and improve reliability. I had modified and expanded my old megasquirt box to its limits. I spent enough money and effort on that setup to buy 2 VEMS probably. I like the do it yourself nature of the Megasquirt project but it was time for something in a cleaner package with all the features I had grafted onto my MS box. The engine is a 2.6 liter stroked version of the Volvo B230. The 16v head is from a related naturally aspirated 4 cylinder Volvo engine. The turbo setup is 62mm Precision turbo and Isuzu NPR intercooler mounted on a custom stainless header. I run E85 for fuel all the time. Best power so far is a touch over 500 at the rear wheels. http://lh4.ggpht.com/_vbAS80jfYUg/S4TtOzlcrlI/AAAAAAAAALE/tx_uve-Rfjs/DSC00316.JPG 2/25/2010 I'm just sorting out the install right now, and have alot more questions than answers. I have learned that VEMS is not Megasquirt. The setup and configuring of the hardware and software is completely different. I was expecting something like Super Megasquirt. Probably tricked by the fact that Megatune is used to tune the tables and configurations. This VEMS is looking to be very good but will take some re-learning. Here is the list of devices and outputs I'll be running on this engine. I think I have the big power suckers on appropriate outputs. == outputs == ||EC36 pin #||Device(s)|| ||7,8,19,20||4x 1600cc low z injectors|| ||33,34||Ford EDIS coil pack wasted spark|| ||6||Bosch 2-wire Idle Valve|| ||9||Boost Control Solenoid|| ||4||Volvo Electric Fan Relay|| ||17||Nitrous Solenoids|| ||3||Shift Light|| ||36||Factory Tachometer|| ||15||2x Bosch 044 Fuel Pumps|| == in == ||27||12mm threaded hall sensor reading 36-1 wheel|| ||1||TPS from Volvo 960|| ||14||Volvo CLT|| ||2||GM open element IAT|| ||ec18-6||Arming Switch for Nitrous|| ||--||Wideband O2|| ---------------------------------------------- Q: First question, will someone answer on my wiki page? Q2: How does this trigger setup look for a 36-1 wheel? At TDC the crank sensor points at tooth #9 http://www.denverspeed.com/gallery2/d/49917-2/vems_trigger.jpg
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.