#    #  
 #    #  
 #    #  
 #   ##  
  ### #  
         

 ______  
(  __  \ 
| (  \  )
| |   ) |
| |   | |
| |   ) |
| (__/  )
(______/ 
         

         
         
  ####   
     ##  
  #####  
 ##  ##  
  #####  
         

         
         
 ##  ##  
 ####### 
 ####### 
 ## # ## 
 ##   ## 
         

 _     
( )    
| |    
| |  _ 
| |_( )
(____/'
       
       

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
This is for my 2L Alfa spider 4 cyl trigger is runing at cam speed 36-1 trigger feeding trigger configed to hall driving 2 wasted coils coil driver 5 and coil driver 6 one if the injector drivers(any one) will feed the servo to control the mec-FI after I found out the generate-config.bat and the upload-config.bat do not work right. I loaded 1.0.36 fw and used a saved MT file I have for my other car then loaded 1.0.73 and changed the stuff like the trigger etc and it seems to have worked. I nolonger get stuff on the com port while triggering too. inside wiring for knock http://www.vems.hu/files/sly/vems_inside.jpg '''Hall''' showing the tooth cut out of my Spica pump drive wheel had 36 teth now I only have 35 left. http://sly.gotdns.com/images/pickup/FI_wheel_pickup_closeup.jpg This is my 2nd proto http://sly.gotdns.com/images/pickup.jpg http://sly.gotdns.com/images/pickup_split.jpg http://sly.gotdns.com/images/pickup_in_cover.jpg This is my first proto I will remake it now and clean stuff up http://www.vems.hu/files/sly/hall.jpg http://www.vems.hu/files/sly/hall2.jpg ---- ---- ---- http://www.vems.hu/files/sly/megasquirt200507080255.msq http://sly.gotdns.com/images/scope.gif * Where is your system description ? * Where are your tables ? '''Notes''' * For outputs, you should prefer that ECU pulls to GND5 when active. This way any output (with sufficient current capability) can be used easily. Although stepper outputs can drive to high, you can invert them so they drive low when active. This way it is easier to change outputs. Changing output can be necessary in a clone-install that uses stepper outputs for ignition or stepper idle, or in your install if the given output is damaged (or misbehaving, or just for test). See GenBoard/Manual/DigitalOut. To use active-low : ** fan_channel=56 should be fan_channel=D6 ** fuelpump_channel=36 should be fuelpump_channel=B6 '''config''' primep=00 primep_temp_scaling=A0 cwl=0F cwh=0F cranking_thres=03 awev=00 awev_temp_scaling=00 awec=FF warmup_clt_range[0]=00 warmup_clt_range[1]=00 warmup_clt_range[2]=00 warmup_clt_range[3]=0F warmup_clt_range[4]=50 warmup_clt_range[5]=64 warmup_clt_range[6]=78 warmup_clt_range[7]=8C warmup_clt_range[8]=AA warmup_clt_range[9]=C8 warmup_clt[0]=64 warmup_clt[1]=64 warmup_clt[2]=64 warmup_clt[3]=64 warmup_clt[4]=64 warmup_clt[5]=64 warmup_clt[6]=64 warmup_clt[7]=64 warmup_clt[8]=64 warmup_clt[9]=64 warmup_rpm_scale=DE req_fuel=0C divider=02 alternate=10 injopen=00 battfac=10 kpafac=7E kpaoffs=A7 injocfuel=00 injrampup_battfac=00 injpwm=FF injpwmt=00 als_launch_input=CF rpmk[0]=0B rpmk[1]=B8 tpsdot_kpadot_conf=00 tpsdotrate[0]=0A tpsdotrate[1]=14 tpsdotrate[2]=28 tpsdotrate[3]=A0 tpsaq[0]=02 tpsaq[1]=02 tpsaq[2]=02 tpsaq[3]=02 als_cut_mintps=FF tpsasync=00 acmult=FF tpsacold=05 launch_enrich=64 launch_retard=0A overrun_fuelcut=3C overrun_fuelresume=37 rev_limit=41 airden_ignore=62 config11=31 config12=30 config13=02 batt_cal=CE fastidle=80 als_max_cut=00 dbaro=0C tps_low=1B tps_high=9F fan_temp=E1 fan_hyst=09 fan_channel=67 iac_step_seq=C9 iac_conf=18 iac_max_steps=F0 iac_tps_thres=03 iac_cold_idle_temp=A0 iac_warm_idle_temp=CF iac_cold_rpm=6E iac_warm_rpm=6E iac_cold_start_pos=BF iac_warm_start_pos=A6 iac_afterstart_rpm=0A iac_afterstart_duration=1E iac_speed=01 iac_kp=19 iac_ki=05 iac_kd=05 launch_rpm=36 iac_integral_limit_dec=46 iac_integral_limit_inc=14 iac_integral_deadband=01 iac_deadband=02 als_cut_maxtps=FF iac_overclose_interval=05 iac_ref_pos[0]=94 iac_ref_pos[1]=91 iac_ref_pos[2]=8F iac_ref_pos[3]=8C iac_ref_pos[4]=8C iac_ref_pos[5]=8C iac_ref_pos[6]=8C iac_ref_pos[7]=8C iac_ref_pos[8]=8A iac_ref_pos[9]=8A iac_sol_channel=7F iac_ign_slope=08 softrpm_range=50 iac_ign_advance_limit=28 iac_ign_retard_limit=18 iac_ign_threshold=00 ego_conf=06 ego_lag=0C ego_coolant=00 ego_maxtps=00 ego_maxmap=6E ego_minrpm=03 ego_maxrpm=FF ego_warmup=15 ego_lean_limit=80 ego_rich_limit=80 ego_pid_kp=28 als_enrich=00 ego_delta=03 ego_target=19 ego_pid_window=FF wbo2_warmup_ramp=9C als_react_tps=FF wbo2_abs_limit=E4 wbo2_limit_maxt=A0 wbo2_fallback=60 wbo2_retry_t=06 wbo2_edgetime_corr=BA wbo2_edgetime_min=50 wbo2_ri_target=96 wbo2_nernstdc_target=88 wbo2_pump_pw_zero=67 wbo2_calibration=A8 wbo2_heater_pid_kp=46 wbo2_heater_pid_ki=10 wbo2_heater_pid_kd=1A wbo2_heater_pid_ilimit=80 wbo2_pump_pid_kp=15 wbo2_pump_pid_ki=4E wbo2_pump_pid_kd=00 wbo2_pump_pid_ilimit=84 wbo2_ri_confidence_scale=80 knock_conf=00 knock_sampling_window=FF knock1_frequency=29 knock1_gain=3F knock1_integrator=1F knock2_frequency=29 knock2_gain=3F knock2_integrator=1F knock_threshold=FF knock_noise_scale=FF knock_max_retard=FF knock_default_retard=00 knock_retard_step=FF knock_retard_delay=FF knock_advance_step=FF knock_advance_delay=FF knock_minrpm=64 knock_maxrpm=64 ve_learn_coolant=90 ve_learn_max_power=00 ve_learn_rpm_scale=00 ve_learn_kpa_scale=00 ve_learn_ego_scale=64 ve_learn_min_weight=01 ve_learn_speed=FF ve_learn_limit=21 ve_learn_conf=03 lcd_c0=FE lcd_delay=FF lcd_backlight=FF kpa_conf=21 ign_balance=00 als_retard_mintps=FF als_retard_maxtps=FF lcd_default_view=00 primary_trigger=00 secondary_trigger=02 tooth_wheel=23 trigger_tooth=00 another_trigger_tooth=09 crank_minper=50 tooth_wheel_twidth1=02 tooth_wheel_twidth2=06 cam_sync_r_edge_phase=3C cam_sync_f_edge_phase=50 reset_engphase_after=6E ign_tdcdelay=62 ign_dwell14=42 ign_dwell6=1E ign_crank_advance=20 ign_out=72 ignchmax=03 engine_off_delay=08 pump_on_mintime=13 fuelpump_channel=3F inj_stage2_rate=FF inj_stage2_start_tps=FF inj_stage2_start_map=FF als_deact_rpm=FF als_deact_time=00 als_deact_egt=00 als_retard=00 als_rev_limit=64 misc1out_minrpm=3C misc1out_maxrpm=41 misc1out_mintps=00 misc1out_maxtps=FF misc1out_minmap=00 misc1out_maxmap=FF misc1out_channel=47 misc2out_minrpm=41 misc2out_maxrpm=46 misc2out_mintps=00 misc2out_maxtps=FF misc2out_minmap=00 misc2out_maxmap=FF misc2out_channel=07 act_wot_rpm=46 act_wot_channel=17 act_rpm_rpm=FF act_rpm_channel=FF egt1_cal=4A als_tks_channel=0F boost_conf=00 boost_targetoffs=00 boost_minpressure=FF boost_pid_kp=20 boost_pid_ki=80 boost_pid_kd=01 boost_pid_ilimit=FF boost_channel=FF water_pump_temp=00 hybrid_rpm_a=00 hybrid_rpm_m=00 water_pump_hyst=00 water_pump_channel=FF toothrel_normal=B5 toothrel_missing=76 fuelcut_min_kpa=28 fuelcut_max_kpa=78 tach_channel=46 tach_div=01 shiftcut_conf=65 shiftcut_channel=FF shiftcut_time=FF softrpm_rpm=41
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.