##   
         
    ##   
    ##   
    ##   
    ##   
    ##   
  ###    

         
|\     /|
| )   ( |
| | _ | |
| |( )| |
| || || |
| () () |
(_______)
         

     ##  
     ##  
  #####  
 ##  ##  
 ##  ##  
 ##  ##  
  #####  
         

###      
 #####   
 ##  ##  
 ##  ##  
 ##  ##  
 ##  ##  
######   
         

 __     __
 \ \   / /
  \ \ / / 
   \ V /  
    \_/   
          

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
=== Alfa Milano(75) gold === First pass will be a PNP in to the L-junk plug. I need to do this fast. Will be using hall dizzy trigger. Will feed a Street Fire CDI unit for spark === NOTE: Lo-Z Injectors === == From verde page == ---- == Spark setup == ---- == Injection == Using old wires. I need to look at the car but the diagram out of the online books page E-43 each injectors has a red wire for power via S2 relay '''looks UNFUSED!!!''' To ECU || '''L-jet Pin''' || '''Wire Color''' || '''Injector #''' || number in setup || ECIII pin || || pin#31 || Light-blue/yellow || 6 || INJF || pin18 || || pin#30 || White/red || 5 || INJE || pin9 || || pin#14 || Light-blue/red || 4 ||INJD || pin20 || || pin#32 || Yellow/black || 3 || INJC || pin8 || || pin#33 || Orange/white || 2 || INJB || pin19 || || pin#15 || Green/white || 1 || INJA || pin7 || ---- == TPS == ||||||'''TPS switch''' (need to get a motronic pot type)|| || '''L-jet Pin''' || '''Wire Color''' || '''Use''' || number in setup || ECIII pin || || pin#18 || Purple || common || TPS || pin1 || || pin#3 || Yellow || WOT || TPS5V || pin28 || || pin#2 || White || idle || GND || pin26 || ---- == IAC == will use the same pins the powered the heater in the old thermo type one pin goes to the S2 power fuel pump/O² Orange/black need to add a flyback diode between the pins. || '''L-jet Pin''' || '''Wire Color''' || '''Use''' || number in setup || ECIII pin || || pin#34 || Orange || will be the IAC control || INJG || pin6 || || N/A || || S2 power || N/A || N/A || ---- == S2 Relay enable == it looks like l-jet pin#28 Yellow/red need to go to ground to enable the S2 double relay ---- == Fuel Pump/O² Power Control == l-jet pin#4 Grey/green looks to high while cranking and will power part of S2 fuel pump/O² ||||||'''Fuel Pump/O² Power Control''' || || '''L-jet Pin''' || '''Wire Color''' || '''Use''' || number in setup || ECIII pin || || pin#20 || Pink/black || looks to power S2 fuel pump/O²|| STEP_A || small#4 || ---- == Fan == |||||| '''Fan Reley''' || || '''Wire Color''' || '''Use''' || '''ECIII18 pin''' || || || STEP_C || 5 || ---- == Tachometer == ||||||||||'''Tachometer''' || || '''L-jet Pin''' || '''Wire Color''' || '''Use''' || number in setup || ECIII18 pin || || Spark3 ||Green/black || coil also goes to cluster(tach?) || STEP_B || 10 || ---- == WBO² == ground the green coex to gnd |||||||||| '''WBO²''' || || '''L-jet Pin''' || '''Wire Color''' || '''Use''' || '''ECIII18 pin''' || WBO² pin || ||part 9|| Light-blue/white || PUMP(-) || 7 || 5 || ||12||Light-blue/black || PUMP(+) || 9 || 6 || ||24||Green coex|| NERNST_CELL1 || 13 || 1 || ||part 6||Green|| HEATER1(-) || 18 || 4 || ||N/A|| Orange/black ||Power || N/A || 3 || |||||||||| Power will come from the old wire that went to the NBO²|| ---- == Knock == |||||||| '''Knock''' Use one of the big green coex|| || '''Wire Color''' || '''Use''' || number in setup || ECIII pin || || Yellow ||KNOCK1 || || 34 || || Shield || Knock gnd || || 36 || || Black || KNOCK2 || || 23 || ---- == Crank Trigger == |||||||| '''Crank Trigger''' Use one of the big green coex|| |||||||| Tie the coex shield only to the VR shield || || '''Wire Color''' || '''Use''' || number in setup || ECIII pin || || Yellow || || TRIGG1_CONN || 27 || || Black || || GND || 26 || ---- == CAM Triger == |||||||| '''CAM Triger''' use the black coex || || '''Wire Color''' || '''Use''' || number in setup || ECIII pin || || 1 || Yellow || TRIGG2_CONN || 13 || || 8 || Brown/White || GND || 26 || || 27 || Grey/red || 5V || 27 || || N/A || Red/black || 12V || N/A || ---- == CLT == || '''L-jet Pin''' || '''Wire Color''' || '''Use''' || number in setup || ECIII pin || || 13 || Brown || CLT || CLT || 14 || || N/A || Black || Gnd || Gnd || 26 || ---- == IAT == || '''L-jet Pin''' || '''Wire Color''' || '''Use''' || number in setup || ECIII pin || || N/A || || || MAT || 2 || || || || Gnd || Gnd || 26|| ---- == Serial Port == || '''Wire Color''' || '''Use''' || number in setup || ECIII18 pin || || Red || RxD || RxD || 14 || || Brown || TxD || TxD || 15 || ---- == Power == ---- |||||| '''Power''' || || '''L-jet Pin''' || '''Wire Color''' || '''Use''' || number in setup || ECIII pin || || pin#20 || Red || power shaired with injectors from S2 || N/A || N/A || || pin#10 || Red/black || power direct from S2 ||+13.8VBATT || 25 || |||||| '''Grounds''' || || '''L-jet Pin''' || '''Wire Color''' || '''Use''' || number in setup || ECIII pin || || pin#5 || Black || ground to CLT || GND || 26 || || pin#16 || Black || power grounds || GND5 || 32 || || pin#17 || Black || power grounds || GND5 || 21 || || pin#35 || Black || power grounds || GND5 || 5 ||
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.