##      
 ##      
 #####   
 ##  ##  
 ##  ##  
 ##  ##  
         

 __  __
 \ \/ /
  \  / 
  /  \ 
 /_/\_\
       

   ##    
   ##    
 ######  
   ##    
   ##    
   ##    
    ###  
         

         
   ##    
         
  ###    
   ##    
   ##    
  ####   
         

 _       
( (    /|
|  \  ( |
|   \ | |
| (\ \) |
| | \   |
| )  \  |
|/    )_)
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
== ''' This is the set up for my 1987 Alfa Milano Verde ''' == others here MembersPage/TomPhillips MembersPage/JisopPark also online Workshop Manuals http://www.users.on.net/~craigf/ see http://www.alfabb.com/bb/forums/showthread.php?t=26315 *''' block is now a S ''' *pickup will be VR on a 60-2 *COPS (Coil On Plug) *cam trigger at some point but not yet *use 164 intake(cut to fit) with the longer runners tuned to the S cams *179.91CID 2.949L * stock injectors 18LB * Req_Fuel 17.5ms http://www.megamanual.com/v22manual/mfuel.htm#reqfuel I guess I cut that in half 8.75ms I changed the coil mosfet resistors to 1K (feeding the Base)and put in PNP 2N3906 at Q3 Q6 Q9 Q12 Q16 Q21 Emitter to power Collector to the outputs ---- '''COP setup''' The pairs I will use so I can run wasted is ---- Q16,Q21 #0,#1 pin53,pin33 ---- Q6,Q9 #4,#5 pin11,pin12 ---- Q12,Q3 #6,#7 pin10,pin24 ---- ---- '''Injection''' using old wires need to look at the car but the diagram out of the online books page E-43 each injectors has a red wire for power via S2 relay '''looks UNFUSED!!!''' To ECU Light-blue/yellow l-jet pin 31 White/red l-jet pin 30 Light-blue/red l-jet pin 14 Yellow/black l-jet pin 32 Orange/white l-jet pin 33 Green/white l-jet pin 15 ---- ||||||'''TPS switch''' (need to get a motronic pot type)|| || '''L-jet Pin''' || '''Wire Color''' || '''Use''' || || pin#18 || Purple || common || || pin#3 || Yellow || WOT || || pin#2 || White || idle || ---- IAC will use the same pins the powered the heater in the old thermo type one pin goes to the S2 power fuel pump/O² Orange/black l-jet pin#34 Orange will be the IAC control ---- it looks like l-jet pin#28 Yellow/red need to go to ground to enable the S2 double relay l-jet pin#4 Grey/green looks to high while cranking and will power part of S2 fuel pump/O² l-jet pin#20 Pink/black looks to power S2 fuel pump/O² l-jet pin#1 coil also goes to cluster(tach?) ---- == Power == ---- |||||| '''Power''' || || '''L-jet Pin''' || '''Wire Color''' || '''Use''' || || pin#20 || Red || power shaired with injectors from S2 || || pin#10 || Red/black || power direct from S2 || |||||| '''Grounds''' || || '''L-jet Pin''' || '''Wire Color''' || '''Use''' || || pin#22 || Black || ground to CLT and thermostat case || || pin#16,pin#17,pin#35 || Black || power grounds ||
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.