_____ 
 |_   _|
   | |  
   | |  
   |_|  
        

         
|\     /|
| )   ( |
| | _ | |
| |( )| |
| || || |
| () () |
(_______)
         

 _       
( (    /|
|  \  ( |
|   \ | |
| (\ \) |
| | \   |
| )  \  |
|/    )_)
         

         
|\     /|
| )   ( |
| (___) |
|  ___  |
| (   ) |
| )   ( |
|/     \|
         

       _ 
      | |
      | |
  _   | |
 | |__| |
  \____/ 
         
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
Inline 5-cylinder, sequential ignition with camsync Primary trigger: 60-2 w/ VR sensor. Secondary trigger: Single tooth w/ Hall sensor. Firing order is 1-2-4-5-3. ---- MembersPage/RonnieH has set up VEMS on a very similar motor also with seq. COP. After some additional reading, his settings seem obsolete due to code changes. Primary trigger settings ||Field name ||Variable name|| Value [decimal] (Value [hex])||Comment|| ||Primary Trigger || primary_trigger || 1 (0x01)|| For multi-tooth trigger without filtering (I think). 0x09 is with filtering? Which should I use?|| ||Edge || || ||Rising || ||Type || || ||Multitooth || ||Filtering...Bit7 || || ||Disable || ||Number of teeth on wheel || tooth_wheel || 58 (0x3A)|| || ||Trigger tooth ||trigger_tooth || 6 (0x06) (from memory, need to confirm on engine itself) || Look at the tooth under the sensor at TDC of cylinder 1, count backwards the number of teeth required to be ~60 degrees BTDC, the tooth now under the sensor is trigger_tooth || || || ign_tdcdelay || 120 (0x78) || Number of degrees BTDC that trigger_tooth is located at, in units of 0.5 degrees. Ex: If trigger tooth is located 60 degrees BTDC, then ign_tdcdelay is 60 * 2 = 120 decimal = 78 hex. Thanks to MembersPage/BorisRieken/PrimairyTrigger for actually taking time to write this shit out.|| ||Next trigger tooth ||another_trigger_tooth || 24 (0x18) || (from GenBoard/UnderDevelopment/FirmWare/TriggerRelated, 60 (teeth on the wheel) * 2 (wheel revolutions per cycle) / 5 (ignition events) = 24 teeth between events|| ||Crank min. period || crank_minper || 188 (0xBC) || 60 (seconds) / 8000 (max rpm) / 5 (number of engine events) * 2 = 0.003 (seconds) = 3000 (microseconds). In units of 16usec, so 3000usec / 16 = 188 [decimal] = BC [hex]. Can someone confirm this is the correct formula? Or even what this value means? || || ||tooth_wheel_twidth1 || 24 (0x18) ||Width of a single tooth on wheel, in quarter degrees (360/60 = 6 degrees per tooth, 6*4 = 24 quarter degrees per tooth, 24dec = 18hex)|| || Tooth relation normal || || 122 || According to Megatune F1 menu. Seems attached to multi_tooth trigger with filtering. Clarification? || || Tooth relation missing || || 181|| According to Megatune F1 menu. Seems attached to multi_tooth trigger with filtering. Clarification? || ---- Secondary trigger settings ||Field name ||Variable name|| Value [decimal] (Value [hex])||Comment|| || ||secondary_trigger || (0xFE) || For rising edge trigger || || ||tooth_wheel_twidth2 || 0 (0x00) ||Not sure on this one either, changelog says set this to 0, but why?|| ---- h[1] is reftooth array. Do I need values here, or should it be all 0's? h[2] is ignchannel array
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.