_____ 
  / ____|
 | (___  
  \___ \ 
  ____) |
 |_____/ 
         
         

         
         
 ##  ##  
 ##  ##  
 ##  ##  
  ####   
   ##    
         

         
         
  ### #  
 #   ##  
 #   ##  
  ### #  
      #  
  ####   

_________
\__   __/
   ) (   
   | |   
   | |   
   | |   
   | |   
   )_(   
         

         
         
  ### #  
 #   ##  
 #   ##  
  ### #  
      #  
  ####   

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
I have still not purchased new injectors, but as of writing I am looking at ''Delphi Multec 1 95 lb/hr injectors'' (~1030cc). Currently trying to find a detailed spec sheet, but with little luck. Here is what I know (from http://www.racetronix.com/17113744FM.html): *Static Flow Rate @ 43.5PSI (300 KPa) = 95.0 lb/hr / 12.0 gm/sec / 998 cc/min *Dynamic Flow Rate @ 43.5PSI (300 KPa) 2.5ms pulse width and 10ms repetition rate = 2.2 gm/pulse *Coil Resistance: 2 Ohms / Low Impedance / Low-Z (Peak/Hold injector drivers required) *Factory Tolerance: +/-5% (actual +/-7%) *Cone Spray Angle - 17.6 degrees - single spray cone. Approximate cone angle for 90% of spray volume *Connector: Minitimer (Bosch EV1) *Ball/Seat Design with 6-Hole Diffuser Disc *Factory fitted with Viton upper and lower o-rings. I have located this Delphi webpage: http://go.delphi.com/CS/dpss/catalog/ProductInformation.aspx?PartProductID=FJ10456 Apparently the Delphi part number is FJ10456. The site lists no other useful information. ---- MembersPage/KevinBlack/InjectorSpecDatabase has a complete looking set of these numbers for the Delphi 95lb/hr injectors. Mirrored here: Delphi Low-Z 95#/hr (with 30v TS diode and 6R8 resistors) * Inj open time @13.2V (us) 0 (because of the 30v flyback, from MembersPage/PhatBob/UserGuide, LowZ section ) * Inj effective rampup (us) 512 * injrampup_battfac (us) 4080 (also because of 30v flyback) * battfac (us) ??? * Injpwm DC (%) 100 * Injpwm DC added @6V (%)0 * Injpwm peak time (ms) 25.5 Any suggestions on the other figures? ---- The low-z injectors will require power resistors. As mentioned earlier, I can source them in almost any spec I want. I understand the resistors are used for current limiting, but how much current am I aiming for? A couple of quick calculations yields a 12ohm resistor for a current of 1A and 5ohm for 2A (both assuming 2ohm injector resistance and 14V supply). PhatBob's UserGuide states that 6.8ohm/50W power resistors yielded good results on 'Delphi 1000cc injectors'. This leads me to believe that they were using the same injectors as I intend to. 6.8ohm/50w resistor, $3.57: http://www.newark.com/26M4936/passives/product.us0?sku=WELWYN-WH50-6R8JI ---- I calculated req_fuel to 2.89 using (6.49 * 2300[cc] / 5 / 1032[cc/min]). Is it worth it to halve this and double my VE values? ---- As of now I plan to use my current Megasquirt fuel map (with values scaled) as a base map.
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.