##    
         
  ###    
   ##    
   ##    
  ####   
         

         
 ### ### 
  ### ## 
  ##     
  ##     
  ##     
 ####    
         

         
         
 ### ##  
 #  #  # 
 #  #  # 
 #  #  # 
 #  #  # 
         

 ###     
  ##     
  ##     
  #####  
  ##  ## 
  ##  ## 
 ###  ## 
         

         
         
 ##  ##  
 ##  ##  
 ##  ##  
  ####   
   ##    
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
I have still not purchased new injectors, but as of writing I am looking at ''Delphi Multec 1 95 lb/hr injectors'' (~1030cc). Currently trying to find a detailed spec sheet, but with little luck. Here is what I know (from http://www.racetronix.com/17113744FM.html): *Static Flow Rate @ 43.5PSI (300 KPa) = 95.0 lb/hr / 12.0 gm/sec / 998 cc/min *Dynamic Flow Rate @ 43.5PSI (300 KPa) 2.5ms pulse width and 10ms repetition rate = 2.2 gm/pulse *Coil Resistance: 2 Ohms / Low Impedance / Low-Z (Peak/Hold injector drivers required) *Factory Tolerance: +/-5% (actual +/-7%) *Cone Spray Angle - 17.6 degrees - single spray cone. Approximate cone angle for 90% of spray volume *Connector: Minitimer (Bosch EV1) *Ball/Seat Design with 6-Hole Diffuser Disc *Factory fitted with Viton upper and lower o-rings. I have located this Delphi webpage: http://go.delphi.com/CS/dpss/catalog/ProductInformation.aspx?PartProductID=FJ10456 Apparently the Delphi part number is FJ10456. The site lists no other useful information. ---- I'd like to have some 'ballpark' figures for the following values. Any suggestions? * Inj. open time @ 13.2V - 1000us * Inj. effective rampup - ?us * injrampup_battfac - ?us * battfac - ?s * Injpwm DC - 100% * Injpwm peak time - ?ms * Divider - ? * Alternate banks from h[0] - 4..0 * Fire banks while cranking - ? MembersPage/KevinBlack/InjectorSpecDatabase has a more complete set of these numbers for the Delphi 95lb/hr injectors. Mirrored here: Delphi Low-Z 95#/hr (with 30v TS diode and 6R8 resistors) * Inj open time @13.2V (us) 0 * Inj effective rampup (us) 512 * injrampup_battfac (us) 4080 * battfac (us) ??? * Injpwm DC (%) 100 * Injpwm DC added @6V (%)0 * Injpwm peak time (ms) 25.5 ---- The low-z injectors will require power resistors. As mentioned earlier, I can source them in almost any spec I want. I understand the resistors are used for current limiting, but how much current am I aiming for? A couple of quick calculations yields a 12ohm resistor for a current of 1A and 5ohm for 2A (both assuming 2ohm injector resistance and 14V supply). ---- I calculated req_fuel to 2.89 using (6.49 * 2300[cc] / 5 / 1032[cc/min]). Is it worth it to halve this and double my VE values? ---- As of now I plan to use my current Megasquirt fuel map (with values scaled) as a base map.
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.