_       
( (    /|
|  \  ( |
|   \ | |
| (\ \) |
| | \   |
| )  \  |
|/    )_)
         

         
         
  ####   
     ##  
  #####  
 ##  ##  
  #####  
         

    ##   
         
    ##   
    ##   
    ##   
    ##   
    ##   
  ###    

 _____ 
(  _  )
| (_) |
|  _  |
| | | |
(_) (_)
       
       

         
         
  #####  
 ##  ##  
 ##  ##  
  #####  
     ##  
 #####   

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
Original intentions of running Delphi 1000cc injectors was scrapped. A friend offered me a set of used Siemens DEKA 1 795cc Low-Z injectors for a great price. Specs (from http://www.racetronix.com/3145FM.html) Static Flow Rate: 74.7 lb/hr = 9.42g/s = 769 cc/min (+/-4%) Dynamic Flow Rate 2.5ms PW @ 100Hz: 16.9 mg/pulse (+/-4%) Coil Resistance: 2.35 Ohms / Low Impedance / Low-Z (Peak/Hold driver circuit required) Spray Pattern: Pencil Connector: Minitimer (Bosch EV1) ---- MembersPage/KevinBlack/InjectorSpecDatabase has a complete looking set of these numbers for the Delphi 95lb/hr injectors. Mirrored here: Delphi Low-Z 95#/hr (with 30v TS diode and 6R8 resistors) * Inj open time @13.2V (us) 0 (because of the 30v flyback, from MembersPage/PhatBob/UserGuide, LowZ section ) * Inj effective rampup (us) 512 * injrampup_battfac (us) 4080 (also because of 30v flyback) * battfac (us) ??? * Injpwm DC (%) 100 * Injpwm DC added @6V (%)0 * Injpwm peak time (ms) 25.5 Barring any new information I will use these as base values for the Siemens injectors. Any suggestions on the figures? ---- The low-z injectors will require power resistors. As mentioned earlier, I can source them in almost any spec I want. I understand the resistors are used for current limiting, but how much current am I aiming for? A couple of quick calculations yields a 12ohm resistor for a current of 1A and 5ohm for 2A (both assuming 2ohm injector resistance and 14V supply). PhatBob's UserGuide states that 6.8ohm/50W power resistors yielded good results on 'Delphi 1000cc injectors'. I have opted for 6R 50W power resistors due to cost and availability. ---- Injector wiring and setup ||Cylinder || Inj. channel || ECU Pin || Mask pattern number [hex] || || 1 || Injector1 || EC36/7 || 1 || || 2 || Injector2 || EC36/19 || 2 || || 3 || Injector3 || EC36/8 || 4 || || 4 || Injector4 || EC36/20 || 8 || || 5 || Injector5 || EC36/9 || 10 || Since the injectors are going to be fired sequentially I want them to trigger on the intake stroke of each cylinder. Assuming the intake stroke starts at 0 crank degrees, when each cylinder is at TDC of it's compression stroke (360 crank degrees later), all the other cylinders will be at the following positions: || || Cyl. 1 TDC || Cyl. 2 TDC || Cyl. 4 TDC || Cyl. 5 TDC || Cyl. 3 TDC || || Cyl. 1 pos. || (360) || 504 || 648 || 72 || 216 || || Cyl. 2 pos. || 216 || (360) || 504 || 648 || 72 || || Cyl. 4 pos. || 72 || 216 || (360) || 504 || 648 || || Cyl. 5 pos. || 648 || 72 || 216 || (360) || 504 || || Cyl. 3 pos. || 504 || 648 || 72 || 216 || (360) || (Arranged in firing order, not numerical order) Because the injectors have to be fired at the same time as the coils fire, we need to sync each cylinder's spark event with an injector event on the intake stroke of another cylinder. The table above assumes that the intake stroke occurs during the first 180 degrees of crank rotation. Looking at where the values fall, cylinder 4 should be on it's intake stroke as cylinder 1 is firing, cylinder 5 as cylinder 2 is sparking, etc. Going over to MembersPage/KarlBuchka/Trigger, we can match the reference tooth array (h[1]) to the injector output array (h[0]) as follows: h[0] = 08 02 01 04 10 00 00 00 I calculated req_fuel to 3.75 using (6.49 * 2300[cc] / 5[cyl] / 795[cc/min]). ---- As of now I plan to use my current Megasquirt fuel map (with values scaled) as a base map.
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.