_   _ 
( ) ( )
| `\| |
| , ` |
| |`\ |
(_) (_)
       
       

         
         
  ### #  
 #   ##  
 #   ##  
  ### #  
      #  
      #  

         
         
 ##  ##  
  ####   
   ##    
  ####   
 ##  ##  
         

  _____ 
 |_   _|
   | |  
   | |  
   |_|  
        

  _      
 | |     
 | |     
 | |     
 | |____ 
 |______|
         
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
I have Genboard 3.3 (1.0.53) installed on my car, and i have some problems with those .bat files installed on my computer. When connected to car, download-config.bat works fine, but when running generate-config.bat it doesn´t work right. Tables.mtt is generated ok, but config.mtt have ERROR text first on every line. At the end it says Config.mtt generated with 255 errors and 0 warnings.??? *check your downloaded config.txt in /config that it is correct *check your /firmware that is has correct global.h in it *if previous doesn't give any results, download new VemsMT release and replace old makeconfig.exe with the one from new package Tried with new .exe file , but still the same... at what com-port is your laptop communicating with genboard? when this is another com-port as the bat-file uses then you have to edit the batfile with a texteditor to adjust its com-port. Tim Edit your config.txt with Programmers notepad, Do not use windows notepad. There is note about this in here somewhere on wiki. I had similar problems because windows notepad somehow mixed up config.txt and give multiple errors when trying to generate config. Then finally editing with Programmers notepad there was many lines containig text from multiple lines. I separated texts to their own lines, saved and everything worked OK! 26.03.07 It look´s to be ok in Programmers notepad.. Is it the global.h then what´s messing up? I doesn´t have com port in generate-config.bat, only in upload and download.bat´s have it. I modified config file with Programmers notepad (removed empty lines) after that, when running generate config, it says on every line: WARNING: did not find a value for ... and so on.. Except at first line it reads: softrpm_rpm=FF01=FF7700F=80 That softrpm is in last line in config.txt There are values in every line when i open config.txt in editor!!! ------------------------------------------------------------ I´ve got false reading in clt and mat at lower temperatures, when temp is like +15c outside,lcd shows then +22 or +23 celsius. CLT shows +96c when engine in at normal temp (+92c thermostat) Sensors are bosch MAT 0280 130 039 and CLT 0280 130 068 and car is Calibra turbo I´ve measured those, and here´s my list: MAT 1c 6140 ohm 10c 4080 ohm 20c 2720 ohm 30c 1840 ohm 40c 1279 ohm 46,5c 1000 ohm 50c 882 ohm 60c 630 ohm 70c 459 ohm 80c 343 ohm 90c 263 ohm CLT - 1c 5770 ohm 10c 3960 ohm 20c 2630 ohm 30c 1760 ohm 40c 1208 ohm 50c 856 ohm 60c 607 ohm 70c 449 ohm 80c 331 ohm 90c 270 ohm I´ve read that easytherm thing but imo it´s bit messy.. So could somebody tell me what to do to get those readings right? What car you have? Can you give the markings on the sensors I.E. Bosch 0 280 130 026. Your measurements are very close to mine. I have hex files to my sensors if you have the same! SeppoRepo Go to filearea and under memberspage/srepo there is zip file containing the files. Tsemppiä! T:Seppo Repo --------------------------------------------------------- 05.05.07 This week i´ve been trying to get that damn cold start correct. It usually dies right after start and on second start is usually ok... I´ve tried to set that afterstart correct but i haven´t found any working setup. Here´s today´s setup: Primepulse 1.0 Hot start scaling 63 Crank cold 11.5 Crank warm 2.9 Crank threshold 300 Crank advance 20 Afterstart enrich 35 Afterstart scaling 15 Duration 402 I´ve tried cwl between 7.5 to 14 and afterstart enrichment 20% - 80&. Warm starts are quite good so that cwh is quite near where it should be, i think... And off course i´ve tried just few times per day, so that the engine is sure enough cold..
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.