_   _ 
| \ | |
|  \| |
| . ` |
| |\  |
\_| \_/
       
       

         
         
 ### ##  
 #  #  # 
 #  #  # 
 #  #  # 
 #  #  # 
         

  _____
 |__  /
   / / 
  / /_ 
 /____|
       

  ____  
 |  _ \ 
 | | | |
 | |_| |
 |____/ 
        

         
         
 #####   
 ##  ##  
 ##      
 ##      
 ##      
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
As my Genboard v3.3 seems to be wired up (see MembersPage/JoelZernask), this page is about the configration. ---- Here are the specs of my engine: * 1989 Audi PT 3,6 liter 32valve V8 * firing order: 1-5-4-8-6-3-7-2 * ignition type: wasted spark * coils: two 2*2 coil packs (Bosch 0 221 503 407) ---- Firmware version used: '''1.0.36''' Here are config.txt and tables.txt as of September 4, 2006 (captured by download_config.bat command in the VemsMT1.0.36 directory): http://pildid.audiclub.ee/joel/kuubik/config.txt http://pildid.audiclub.ee/joel/kuubik/tables.txt Note that these captures were made before the matching of the ignition with the strobe light, so primary trigger degrees are not right here. I will publish new config and tables soon. ---- '''Trigger''' '''Primary-VR''' * NOT multitooth * VR sensor (VR primary-trigger HW used; rising edge configured) * 4 trigger pins on the flywheel, 64 degrees BTDC each cyl ** each pulse 64 degrees BTDC (+/- 1 degree). '''Secondary-HALL''' * 1 Hall cam sync pulse overlapping the crank trigger pin occuring 64 deg before #1 piston reach TDC in it's work phase. * Rising edge 77d BTDC Problems faced with the trigger during the installation process are here: MembersPage/JoelZernask/TriggerPage (chronologically listed, lots of BS) ---- '''Ignition''' Cylinders firing together are: 1 5 4 8 6 3 7 2 The coil packs were planned to be connected as follows (PhatBob's guide): EC36-pin35 to Coil 1 EC36-pin33 to Coil 2 EC36-pin34 to Coil 3 EC36-pin36 to Coil 4 However, drives 00 (EC36-pin35) and 03 (EC36-pin36) appeared disfunctional (probably damaged) on my board, therefore had to be replaced. Therefore cylinders are wired as follows: Cylinders 1 & 6 to Coil 1 to EC36-pin11 drive06 Cylinders 5 & 3 to Coil 2 to EC36-pin33 drive01 Cylinders 4 & 7 to Coil 3 to EC36-pin34 drive02 Cylinders 8 & 2 to Coil 4 to EC36-pin24 drive04 ---- '''Fuel''' Sequential fuel delivery for Audi 3,6 V8 PT engine firing order: 1-5-4-8-6-3-7-2 Bosch injectors 173cc Constant for RPM calculation is 1500. Req fuel is 16,7 (173cc injectors). ----
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.