##    
    #    
    #    
    #    
    #    
    #    
   ###   
         

         
         
  #####  
 ##      
  ####   
     ##  
 #####   
         

    ##   
   #  #  
   #     
 #####   
   #     
   #     
   #     
         

  _____  
 |  __ \ 
 | |__) |
 |  ___/ 
 | |     
 |_|     
         
         

         
         
  ### ## 
 ##  ##  
 ##  ##  
  #####  
     ##  
 #####   

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
Successful conversion to VEMS Genboard 3.2 on my race spec 1985 VW Golf. Pictures and some info: http://proton.shadowflux.com/vwracing/ http://picasaweb.google.com/jamesmweinheimer/Golf http://picasaweb.google.com/jamesmweinheimer/7162007TimeTrialWilsonCircuit http://proton.shadowflux.com/vwracing/golf/pictures/track/ email-james-at-shadowflux-dawt-com ---- 7 May 2007: Decreased coil dwell time to 2.0ms. artificial rev limiter mentioned in 13 Oct 2006 update is gone. Installed and calibrated new wideband O2 sensor. Installed and calibrated EGT sensor in header at collector Installed GM temperature sensors and uploaded same firmware as before (1.0.45), but without patch for Bosch sensors. This gives more accurate readings than manually configured Bosch sensors. ---- 3 October 2007: The suggestion "can you get snapshots (via TerminalProgram) of the wbo2 LCD page (the one with Ri:...). If the Ri or nernst target is not reached, ego correction might be disabled" was made on MembersPage/MattiasSandgren/EgoCorrection mde01 enables wideband O2 sensor parameter dump (mde02 enables wbo2 even with stopped engine, so mde03 does both). Lines like ''w=....'' are emitted via the serial port: that is binary content. "wbo2log.pl" perl script should work capture and format it. Yes, it is still valid. Should run on either Linux or Windows. Source for logging: GenBoard/Manual/Config/WBoxygen ? Is wbo2log.pl still included in newer firmware versions? I do not see it in 1.1.64. Is it still valid? Can some of the tools in the firmare/bin directory of the firmware versions be integrated into VemsTune? ---- Config Latest/revised comments config: MembersPage/JimW/Config Notes about subsystems (to verify/justify config variables) on pages below * MembersPage/JimW/FuelSystem * MembersPage/JimW/InputTrigger * MembersPage/JimW/IgnitionOutput * MembersPage/JimW/AirFeed * MembersPage/JimW/Wiring * MembersPage/JimW/Sensors * Datalogs http://proton.shadowflux.com/vems/datalogs Engine: * 1.8 liter VW 4 cylinder SOHC from 1985 Golf GTI ** 10:1 compression ** Stock bottom end * Solid lifter 8 valve head, code JH ** Ported/polished ** Euro cam ** Bosal/Brospeed 4-2-1 tube header, 2.5 inch exhaust ---- My Genboard and LCD display: http://proton.shadowflux.com/vems/genboard_32_1.jpg http://proton.shadowflux.com/vems/lcd_box_1.jpg http://proton.shadowflux.com/vems/lcd_box_2.jpg http://proton.shadowflux.com/vems/Img_2680.jpg ---- Future Plans: * Add relay and switching gear to properly set up launch and shift control. * Add EGT sensor and hardware if necessary. Completed. * Change connector on endplate for common DB9 cable fitment. Completed. * Change over to standard GM IAT sensor for more accurate readings. Completed. * I'm sure I'll find something else to add here.
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.