_____ 
 |_   _|
   | |  
   | |  
  _| |_ 
 |_____|
        
        

  _  __
 | |/ /
 | ' / 
 |  <  
 | . \ 
 |_|\_\
       
       

###      
 #####   
 ##  ##  
 ##  ##  
 ##  ##  
 ##  ##  
#### ### 
         

         
         
  ####   
 ##  ##  
 ######  
 ##      
  #####  
         

         
         
 #####   
 ##  ##  
 ##  ##  
 #####   
 ##      
 ##      

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
Successful conversion to VEMS Genboard 3.2 on my race spec 1985 VW Golf. Pictures and some info: http://proton.shadowflux.com/vwracing/ More pictures: http://pg.photos.yahoo.com/ph/jerrysno1kid/album?.dir=fa25re2&.src=ph&store=&prodid=&.done=http%3a//pg.photos.yahoo.com/ph/jerrysno1kid/my_photos email james at shadowflux dot com ---- While browsing the net I came upon this thread about someone using 034EFI on their turbo VR6 VW Golf. The 034EFI setup looks very nice. The thread is located at: http://forums.vwvortex.com/zerothread?id=2470106&page=6 ---- Progress 9 July 2006: Firmware r045, Megatune for 1.0.36 On conversion from firmware r023 several options were left unset in config which threw everything off quite a bit. Be sure to review all pages and set config accordingly. Enabling antilag and launch by accident will prevent engine from running. * Fuel cut was defaulted to 0kPa which confused me for a few minutes when it would fire while cranking but never start. * Autotune still wants to drag my VE values down to zero, even though they VE figures are fairly accurate. Anyone else experiencing similar problems? * Spark cut idle control works nicely, but now there are several pages for idle settings. Consolidation possible to avoid confusion? * Having trouble spinning motor faster than 6000 rpm. Can someone review my config (good03.msq) and recent datalogs and give some comments please? ---- Progress report (Nov 11): Firmware r023 Starts and runs! Idles fairly smoothly with only set-screw holding throttle body at 4-5% open. Drove around a little bit, runs very well and all parameters look good. Accelerates much harder than when K-Jet was running the show, until it gets to the sections of fuel map I haven't tuned. I'll be reviewing logs today, updating tables and doing more testing, provided the rain stays away. Thank you, everyone, for your help! * Notes: * * VE table values had to be doubled even though req_fuel was set at value recommended by req_fuel calculators. * * Top dead center after trigger was retarded by 30 crank degrees. * * Use MegaTune to enable/disable features (misc_out, boost control, iac, etc). Disable values in config.txt inconsistent between feature channel outputs. * * LCD display is cutting out, displaying with strange offsets, otherwise acting funny. Vibration getting to headers or wiring elsewhere? Will test. ---- Config Latest/revised comments config: MembersPage/JimW/Config Notes about subsystems (to verify/justify config variables) on pages below * MembersPage/JimW/FuelSystem * MembersPage/JimW/InputTrigger * MembersPage/JimW/IgnitionOutput * MembersPage/JimW/AirFeed * MembersPage/JimW/Wiring * MembersPage/JimW/Sensors * Datalogs http://proton.shadowflux.com/vems/datalogs ---- My Genboard and LCD display: http://proton.shadowflux.com/vems/genboard_32_1.jpg http://proton.shadowflux.com/vems/lcd_box_1.jpg http://proton.shadowflux.com/vems/lcd_box_2.jpg ----
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.