__          __
 \ \        / /
  \ \  /\  / / 
   \ \/  \/ /  
    \  /\  /   
     \/  \/    
               
               

 _   _ 
| | | |
| | | |
| | | |
\ \_/ /
 \___/ 
       
       

      _ 
     | |
  _  | |
 | |_| |
  \___/ 
        

  ____  
 |  _ \ 
 | |_) |
 |  __/ 
 |_|    
        

         
         
  ####   
     ##  
  #####  
 ##  ##  
  #####  
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
Switching to Genboard on my Golf racer, because K-Jet isn't cutting it. Later on I will be doing forced induction, so I need room for change. Pictures and some info: http://proton.shadowflux.com/vwracing/ email james at shadowflux dot com ---- I'm pretty sure I finally got the manual.xml commited to CVS at the end of the night. Someone please check it for me. If it is updated as I stated (version 1.37), please review so we can start using it. Thanks. ---- WBO2 question: All wiring is correct, I have double checked. wbo2_pump_pw (0x63) is calibrated correctly, voltage is -0.03V. Measured Rcal at 127 ohms, so wbo2_calibration is set to 0xB0. Attached sensor to do free air calibration, command mde02, sensor heat comes up to maximum (0xE4) and O2% appears on LCD mlp07. As soon as heat is maxed, drops to 0x00, pauses then comes up to a reasonable level gradually. As soon as O2% appears on screen, value changes VERY rapidly from 20.9x% to 11.xx% to 17.xx% to 19.xx%, in no particular order. Ri stays between 0x90 and 0xAD. Any ideas what is going on here? All of this is without engine running. More info: Did some testing last night with 100ohm resistor method. Nernst was at 3.96V at first (nernst_dc_target=8D), raised it gradually to 0xBD to get to 4.47V. (I suspect that integral was too low, not enough to push PID error down to zero) Intermediate nernst_dc_target values resulted in wavering (by about 0.2V, instead of the max 0.1V allowed maximum) Nernst voltage. When nernst_dc_target was raised to 0xBD, Nernst voltage was dead steady at 4.47v (maybe pump was railed at max FF?). WBO2 testing page says I need '''3.96V+0.45V=4.41V''' sortof steady, so lowered nernst_dc_target to 0xB7, but voltage started to waver again. With values where Nernst voltage wavers, pump value (on mlp07 of LCD) is a value such as 0xC3, jumps to FF briefly, then back down to 0xC3 (0xC3 is just an arbitrary number. actual value is above 0xC0, but I don't remember what it was). When measuring nernst and pump-, I have varying values. I think the values i measured were bouncing between 120mv and 150mv. They are written down at home, I will post later. I changed wbo2_pump_pidki from 0x40 to 0x20, but didn't see a difference in voltage values. Should this affect the bouncing of voltage up and down when measuring nernst (to ground) voltage and nernst to pump- voltage? yes, it sounds like a WBO2 PID configuration issue (oscillation), because your WBO2 pump (HW) seems to react. Play with the values, especially pump_pid.... eg. try this: * wbo2_pump_pid_kp=30 * wbo2_pump_pid_ki=80 * wbo2_pump_pid_kd=00 * wbo2_pump_pid_ilimit=80 Wow Marcel, those settings were VERY close to dead on. Only had to adjust the wbo2_calibration and bring nernst_dc_target back down to reasonable values. Got the WBO2 working tonight before I loaded it onto the trailer. Thanks! I will post updated config after I get back.0 ---- '''RPM reading issue''' Ignition is controlled by ... (GenBoard ?) Injection is contolled by ... (GenBoard ?) Made a log of rpm, it reads 3000-4000 rpm at idle, which is really 900-1000 rpm. RPM drops to ~600 for two to three samples, then back up to 3-4k. * These are symptoms of reversed wires on VR, correct? ** not really, but capture InputTrigger/TriggerLog at cranking and it'll show reversed VR * another_trigger_tooth=12 (decimal 18) is correct for a 36-1 tooth (tooth_wheel=23) and 4-cylinder If the VR is shared with another ECM, we need to examine the situation further (maybe a 10uF 1210 size series cap needed). ---- Config Latest/revised comments config: MembersPage/JimW/Config Notes about subsystems (to verify/justify config variables) on pages below * MembersPage/JimW/FuelSystem * MembersPage/JimW/InputTrigger * MembersPage/JimW/IgnitionOutput * MembersPage/JimW/AirFeed * MembersPage/JimW/Wiring * MembersPage/JimW/Sensors ---- My Genboard and LCD display: http://proton.shadowflux.com/vems/genboard_32_1.jpg http://proton.shadowflux.com/vems/lcd_box_1.jpg http://proton.shadowflux.com/vems/lcd_box_2.jpg ----
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.