##  ##  
  ####   
   ##    
  ####   
 ##  ##  
         

 #       
 #       
 # ###   
 ##   #  
 #    #  
 ##   #  
 # ###   
         

  ____  
 |  _ \ 
 | |_) |
 |  __/ 
 |_|    
        

         
         
  ###    
     #   
  ####   
 #   #   
  ### #  
         

 __   __
 \ \ / /
  \ V / 
   > <  
  / . \ 
 /_/ \_\
        
        

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
'''Pin-out''' ''work in progress'' ||'''VEMS Pin-Out'''||'''Function'''||'''Wiring Colour'''||'''Car Pin-Out'''||'''Comments'''|| || EC36-1 || TPS signal || ws/ge 0.35mmý || Pin 5 TB || || || EC36-2 || Intake Air Temp || sw/ro 0.35mmý || PIN 1 IAT || Pin 2 (Ref Gnd - EC36-26) || || EC36-3 || Fast Idle solenoid || || NA || || || EC36-4 || Coil #8 || || NA || || || EC36-5 || Analog Ground || - || - || Ground on the top of the cylinder head || || EC36-6 || Injector G || || NA || || || EC36-7 || Injector A || || Pin 2 || Injector Cyl 1 || || EC36-8 || Injector C || || Pin 2 || Injector Cyl 3 || || EC36-9 || Injector E || || NA || || || EC36-10 || Coil #7 || || NA || || || EC36-11 || Coil #4 || || NA || || || EC36-12 || Coil #5 || || NA || || || EC36-13 || Secondary Trigger || || Pin 2 (signal) || G40 Hall Cam shaft sensor Pin 1(+5V), Pin 3 (Ref Gnd - EC36-26) || || EC36-14 || Coolant Temp || || Pin 1 (Signal) || G62 Coolent sensor , Pin 3 ( Ref. Gnd - EC36-26) || || EC36-15 || Fuel Pump || || Relay (29) || Relay signal to pin 29 || || EC36-16 || Coil #9 || || NA || || || EC36-17 || Injector H || || NA || || || EC36-18 || Injector F || || NA || || || EC36-19 || Injector B || || Pin 2 || Injector Cyl 2 || || EC36-20 || Injector D || || Pin 2 || Injector Cyl 4 || || EC36-21 || Analog Ground || - || - || Ground on the top of the cylinder head || || EC36-22 || Flyback Rail || || NA || Not used - Use EC36-23 || || EC36-23 || Flyback Rail || || - || Solder Internal lead - Ground to engine or batt. || || EC36-24 || Coil #6 || || NA || || || EC36-25 || Vbatt (Switched with ignition - hot in start and on positions) || || - || "Fuse box rail ""30""" || || EC36-26 || Signal Ground || || || Ref. Gnd for TPS, IAT, CLT,CAS... Connect all in wiring Ground to engine or batt. || || EC36-27 || Primary Trigger || || Pin 2 (signal) || VR sensor G28 - Pin 1( Sensor Gnd) , Pin 3 (Shield Gnd, Gnd to battery ) || || EC36-28 || +5V (to sensors) || || - || HALL and other trigger that need +5V || || EC36-29 || +5V (TPS voltage divider) || || - || TPS +5V || || EC36-30 || Drive_11 (misc output) || || NA || || || EC36-31 || Drive_10 (misc output) || || NA || || || EC36-32 || Analog Ground || - || - || Ground on the top of the cylinder head || || EC36-33 || Coil #1 || || Pin 1 (signal) || Cyl 2, Pin 15 (+), Pin 4a (Gnd Cyl. Head) || || EC36-34 || Coil #2 || || Pin 1 (signal) || Cyl 3, Pin 15 (+), Pin 4a (Gnd Cyl. Head) || || EC36-35 || Coil #0 || || Pin 1 (signal) || Cyl 1, Pin 15 (+), Pin 4a (Gnd Cyl. Head) || || EC36-36 || Coil #3 || || Pin 1 (signal) || Cyl 4, Pin 15 (+), Pin 4a (Gnd Cyl. Head) || || || || || || || || || || || || || || EC18-1 || WBo2 #2 Nernst Cell || || NA || || || EC18-2 || Exhaust backpressure || || NA || || || EC18-3 || Fuel pressure || || NA || || || EC18-4 || Stepper motor channel A || || NA || || || EC18-5 || Stepper motor channel C || || NA || || || EC18-6 || Drive_B (misc high current output) || || NA || No FET installed || || EC18-7 || WBo2 Pump - || || (-) on WBO2 || WBO2 || || EC18-8 || WBo2 #2 Pump + || || NA || || || EC18-9 || WBo2 #1 Pump + || || (+) on WBO2 || WBO2 || || EC18-10 || Stepper motor channel B || || NA || || || EC18-11 || Stepper motor channel D || || NA || || || EC18-12 || Drive_A (misc high current output) || || NA || No FET installed || || EC18-13 || WBo2 #1 Nernst Cell || || PIN ??? || WBO2 || || EC18-14 || Free || || Pin 1 (Signal) || Knock sensor G61 - Pin 2 (Ref. Gnd) Pin 3 (Shield Gnd) || || EC18-15 || Free || || Pin 1 (Signal) || Knock sensor G66 - Pin 2 (Ref. Gnd) Pin 3 (Shield Gnd) || || EC18-16 || Dallas 1-wire bus || || NA || || || EC18-17 || WBo2 #2 Heater - || || NA || || || EC18-18 || WBo2 #1 Heater - || || PIN ??? || WBO2 || || || || || || || || Extra Pins || || || || || || || || || || || || - || EGT channel 1 || || || Separat EGT lead || || - || LCD display || || || Separat LCD lead / Connector - DB9 || || - || Keyboard || || || Separat Keyboard Connector - PS2 (wall mounted) || || - || MAP || || || Separat MAP hose connection (Wall mounted) ||
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.