_______ 
(_____  )
     /'/'
   /'/'  
 /'/'___ 
(_______)
         
         

    ###  
     ##  
     ##  
  #####  
 ##  ##  
 ##  ##  
  ###### 
         

         
         
 ##   ## 
 ## # ## 
 ####### 
  #####  
  ## ##  
         

______ 
|  ___|
| |_   
|  _|  
| |    
\_|    
       
       

         
|\     /|
| )   ( |
| |   | |
( (   ) )
 \ \_/ / 
  \   /  
   \_/   
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
Engine specs: * cyl count=6 * main trigger= 60-2 on crank http://www.vems.hu/wiki/index.php?page=MembersPage%2FGergelyLezsak%2FTrigger * T3/T4 turbo 50 A/R Compressor, 0.63 A/R Turbine .57 Trim 3" inlet stage 3 wheel * 440 cc bosch high imp petrol injectors * 50cc/s LPG injectors low imp. ---- [\ MembersPage/JanSaenen/LPG LPG Section] [\ MembersPage/JanSaenen/Links Links] [\ MembersPage/JanSaenen/Buylist Buylist] [\ MembersPage/JanSaenen/Vapourised Injection] ---- '''EGT''' My GenBoard (preassembled '''serialNr=355''') MegaTune will log both mcp3208channel4 and mcp3208channel3 (raw values). However, only mcp3208channel4 is displayed on LCD page0 (mlp00). Raw values mean that the * real_celsius_value = egt1_offs + (raw_value * egt1_cal / 256) where typical values: ** egt1_offs=00 ** egt1_cal=49 (that is decimal 73) ---- '''Peak and Hold''' PWM % lasts typically 1.0 ms. ---- '''Fuses''' These are commonly used : ||'''Current consumer'''||'''Fuse rate'''||'''Description/Comment''|| ||VEMS Genboard||'''3A'''|| It actually draws a couple of hundre mA, but this is the smallest automotive fuse commonly found in gas stations|| ||Lambda||'''5A'''|| || ||Injectors||'''10A'''||This could be the main fuse, and a separate 3A fuse for each injector for safety if you get a short in an injector you could fry the driver with only one main fuse|| ||Ignition coil||'''10A'''||Possibly even higher, depending on the coil primary resistance|| ---- MegaTune is a software to change / tune config/table values in VEMS controller: * How can I select full sequential injection? ** alternate=... (cylcount - 1) ** injection sequence h[0]= ... ** See GenBoard/Manual/DigitalOut, GenBoard/Manual/DigitalOut/Table, ---- '''Connect laptop to the Genboard.''' I can't get the Man => Hello response but when terminal is connected and the genboard is powered up I recieve the following message: <0> After this message communication is lost. I use a usb-serial cable, and a laptop with an AC adapter feed. I've checked and double checked the following things: *EC18pin14, 15 and ground. *Put a extra ground wire between laptop ground and chassisground. *9600 baud, 8 data bits, parity none, stop bits 1, handshake none. In both hardware settings and Terminal settings. *reversed the EC18pin 14 and 15. Result was that I didn't recieve the <0> message at power up any more. *GND5 connections *Power connection The LCD screen displays like it should. No problems there. I got it to work on an old computer. So it's deff some issue with the usb adapter cable or software of some kind. Does anybody have a solution?? ---- mailto: Jan_Saenen at hotmail dot com
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.