######  
  ##  ## 
  ##     
  ##     
 ####    
         

         
         
 #####   
 ##  ##  
 ##  ##  
 #####   
 ##      
 ##      

 ___   
(  _`\ 
| (_(_)
`\__ \ 
( )_) |
`\____)
       
       

  _   _ 
 | | | |
 | | | |
 | |_| |
  \___/ 
        

         
         
  #####  
 ##      
  ####   
     ##  
 #####   
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
My project is to turbocharge a BMW E30 325i M20 engine. A nice link for instaling VEMS on a BMW E30: http://savarturbo.se/~mattias/motor/vems_bmw_e30/ Engine specs: * cyl count=6 * main trigger= 60-2 on crank http://www.vems.hu/wiki/index.php?page=MembersPage%2FGergelyLezsak%2FTrigger * stock internals * T3/T4 turbo 50 A/R Compressor, 0.63 A/R Turbine .57 Trim 3" inlet stage 3 wheel * Oil cooling on pistons http://www.e30tech.com/forum/viewtopic.php?t=5223 * Intercooler will be as big as possible * Lime green 440 cc bosch high imp petrol injectors * Yellow LPG injectors from Keihin low imp. * Prins evapouriser * Techedge WB02 display + logger ---- '''Progress''' *The engine is in the car. Next on the to do list is to built a wire loom and some other stuff. ---- I guess we have a lot in common: [MembersPage/GergelyLezsak] A great guy who's car I deff like to see when it's finished: [MembersPage/MattiasSandgren] ---- [\ MembersPage/JanSaenen/LPG LPG Section] [\ MembersPage/JanSaenen/Links Links] [\ MembersPage/JanSaenen/Buylist Buylist] ---- '''EGT''' My GenBoard (serialNr=355 and 356) has two EGT cables connected to the board, at nearby locations. You can connect two EGT sensors. MegaTune will log both mcp3208channel4 and mcp3208channel3 (raw values). However, only mcp3208channel4 is displayed on LCD page0 (mlp00). Raw values mean that the * real_celsius_value = egt1_offs + (raw_value * egt1_cal / 256) where typical values: ** egt1_offs=00 ** egt1_cal=49 (that is decimal 73) ---- '''Peak and Hold''' set the PWM % and how long the peak should last (typically 1.0 ms). ---- '''Fuses''' These are commonly used : ||'''Current consumer'''||'''Fuse rate'''||'''Description/Comment''|| ||VEMS Genboard||'''3A'''|| It actually draws a couple of hundre mA, but this is the smallest automotive fuse commonly found in gas stations|| ||Lambda||'''5A'''|| || ||Injectors||'''10A'''||This could be the main fuse, and a separate 3A fuse for each injector for safety if you get a short in an injector you could fry the driver with only one main fuse|| ||Ignition coil||'''10A'''||Possibly even higher, depending on the coil primary resistance|| ---- '''New Questions''' MegaTune is a software to change / tune config/table values in VEMS controller: * How is a cam trigger supported? ** GenBoard/Manual/InputTriggerCamSync * How can I select full sequential injection? ** alternate=... (cylcount - 1) ** injection sequence h[0]= ... ** See GenBoard/Manual/DigitalOut, GenBoard/Manual/DigitalOut/Table, ---- '''Input variables where Inj_out is dependant of...''' As my car will be running on Vapourised LPG injection my Inj_output timing will be dependant of Fuelpressure and Fueltemperature. I already have a sensor mounted that's able to collect these values but I don't know how I can add these two input values to the code how injection duration is calculated. *At which input channels can I add these two variables?? So where can I connect the wires to at the VEMS unit?? ---- mailto: Jan_Saenen at hotmail dot com
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.