### #  
 #   ##  
 #   ##  
  ### #  
      #  
      #  

         
         
 #     # 
 #  #  # 
 #  #  # 
 #  #  # 
  ## ##  
         

______ 
| ___ \
| |_/ /
| ___ \
| |_/ /
\____/ 
       
       

 _____ 
/  ___|
\ `--. 
 `--. \
/\__/ /
\____/ 
       
       

         
         
 #####   
 ##  ##  
 ##      
 ##      
 ##      
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
My project is to turbocharge a BMW E30 325i M20 engine. Engine specs: * cyl count=6 * main trigger= 60-2 on crank http://www.vems.hu/wiki/index.php?page=MembersPage%2FGergelyLezsak%2FTrigger * stock internals * T3/T4 turbo 50 A/R Compressor, 0.63 A/R Turbine .57 Trim 3" inlet stage 3 wheel * Oil cooling on pistons http://www.e30tech.com/forum/viewtopic.php?t=5223 * Intercooler will be as big as possible * Lime green 440 cc bosch high imp petrol injectors * IAT sensor: GenBoard/Manual/IntakeAirTemperature I guess we have a lot in common: [MembersPage/GergelyLezsak] A great guy who's car I deff like to see when it's finished: [MembersPage/MattiasSandgren] ---- [\ MembersPage/JanSaenen/LPG LPG Section] [\ MembersPage/JanSaenen/Links Links] [\ MembersPage/JanSaenen/Buylist Buylist] ---- Made my order Cable for serial communication with the GenBoard. Use a 6.3 mm stereo jack female/male. Mount that in your dash somewhere and wire it to the serial pins on the EC18 connector. This involves building a custom serial cable to connect your computer with a male 6.3 mm plug in one end and DSUB9 female in the other end. * notebook and MegaTune to tune the ignition map. Assembled v3.3 controller * ignition driver 8 * Knock and 2 EGT * LCD and PS2 yes * MAP onboard * primary_trigger VR * secondary_trigger HALL Other items: * LCD4x20 28.00EUR * DSUBxx connector 1.00EUR (for LCD) * EC36wire * EC18wire * 2x EGT sensor (K-type) * 2x VEMS sticker * IntakeAirTemp sensor ---- '''Electric fan''' Will need to apply a relay, since there is no output for 30A. Several injector FETs can be driven in parallel, but this is not recommended (very easy to burn traces with misconfiguration). Check GenBoard/Manual/DigitalOut/Table and determine a free output you want to use to control the relay. ---- '''EGT''' My GenBoard (serialNr=355 and 356) has two EGT cables connected to the board, at nearby locations. You can connect two EGT sensors. MegaTune will log both mcp3208channel4 and mcp3208channel3 (raw values). However, only mcp3208channel4 is displayed on LCD page0 (mlp00). Raw values mean that the * real_celsius_value = egt1_offs + (raw_value * egt1_cal / 256) where typical values: ** egt1_offs=00 ** egt1_cal=49 (that is decimal 73) ---- '''Peak and Hold''' -How is the signal to the injectors configured. I checked the board for it's flyback and it's there. The drivers and the LowZ type but how is the signal to the injectors configured? I need a Peak and Hold steering. ---- mailto: Jan_Saenen at hotmail dot com
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.