_______ 
(  ____ \
| (    \/
| (__    
|  __)   
| (      
| )      
|/       
         

         
|\     /|
| )   ( |
| (___) |
|  ___  |
| (   ) |
| )   ( |
|/     \|
         

      _ 
     | |
  _  | |
 | |_| |
  \___/ 
        

         
         
  ####   
 ##      
 ##      
 ##      
  ####   
         

     ##  
     ##  
  #####  
 ##  ##  
 ##  ##  
 ##  ##  
  #####  
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
[MembersPage/JanSaenen] Current state: Used MembersPage/PhatBob/UserGuide and Firmware .38 I'm using a BMW M20 6 cylinder engine simular to MembersPage/GergelyLezsak It uses the following sensors and injectors: *440CC injectors Bosch *Stock single coil distributer *VEMS Internal Map sensor (working) *VEMS shop IAT sensor (working) *WB02 5057 sensor (working) *Other CLT sensor (working) *Volvo TPS sensor (working) *Stock VR sensor (working) ---- ''''16-06-06'''' Trying to figure out the primary triggger settings. This brings some questions along. '''Tooth numbering starts at 0, with 0 being the first tooth after the missing ones.''' * '''What is ment by the next trigger tooth?''' engine event spacing expressed in toothcount **Next trigger tooth is how many trigger teeth between "events". So for a 6 cylinder, ** another_trigger_tooth=14 # = decimal 20 since 6 cyl has 3 events per crank rotation, so 60/3=20 (for a v8 with 36-1: 36/4=9) Note that this does not have to change if you change the "trigger tooth" parameter) * '''What is ment by angular width to reset the enginefase?''' I don't have a cam sensor and it's a four-stroke 6 cilinder engine. So my firing order has to be reset after 720 degrees. Cilinder 1 at 0 degrees, Cil 5 at 120 degrees .......... Cilinder 4 at 600 degrees and Cil 1 again at 720 degrees. ** I think it doesn't matter even if you neglect it for now. Docs suggest decimal 240 for 60-2 wheel * '''What is ment by angular width of tooth?''' ** 2 * '''What is ment by angular width of missing tooth?''' ** 6 Based on this my primary trigger settings in decimal should be: *Rising *Multitooth *Disabled *Disabled *Disabled *Disabled *56 (deg) TDC after the trigger **Careful: This is the number of degrees after the trigger tooth as defined in the "trigger tooth" parameter. *58 Number of teeth on wheel *5 Trigger tooth *20 Next trigger tooth *2 Angular width of tooth *121 Tooth rel normal (Not relevant) *181 Tooth rel missing (Not relevant) *6 Angular width of missing tooth *240 engine fase, when to reset I'll look at my notes tonight. I wrote a spreadsheet for my car that I can pass on to you if you need. '''That would be great!''' [dnb] ---- '''IAT and CLT:''' [/MembersPage/JanSaenen/Tempsens] ---- ''''Fuelpump'''' [/MembersPage/JanSaenen/Fuelpump]
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.