_______ 
(  ____ \
| (    \/
| (__    
|  __)   
| (      
| (____/\
(_______/
         

 _______ 
(  ____ \
| (    \/
| (__    
|  __)   
| (      
| )      
|/       
         

         
  #####  
 ##      
  ####   
   ####  
 #    #  
 #####   
         

   #     
   #     
 #####   
   #     
   #     
   #  #  
    ##   
         

         
         
 #####   
 ##  ##  
 ##  ##  
 ##  ##  
 ##  ##  
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
I've fitted a 20V 4AGE in my AE86 so now I've got it running using VEMS. I'm close to have the diagram for the harness done but I'm not quite sure how to run the trigger. I would like to use the sensors in the distributer. Its got three sensors: * primary trigger is 24 camteeth * secondary trigger is one camtooth. ** actually 2 different sensors positioned 180 (crank-?)degrees apart sense the same campulse. You only need one of thosesensors. We call this arrangement 24+1 (not 12-1 as no missing tooth !) I'll try '''making it work with the 24+1 setup first'''. If this fails I'll go 36-1. You should be able to '''get it work on 24+1''' (eg. 1.1.27 firmware), it's by far the most frequently used from the InputTrigger/MultiToothNoneMissing family. Just beware of polarity if VR (or the edge if HALL - iirc it is VR) and measure signal DC bias when connected to VR trigger input and ignition on (and take note). Someone chose hw swap and installed 36-1 on a 16V (maybe it was before 2007, or he just likes the more precise timing from crank? If wheel is made in smallworkshop, 12-1 cranktooth with HALL sensor recommended): http://www.autosportlabs.net/images/e/e3/Edis_sensor_bracket.jpg http://www.autosportlabs.net/images/6/6c/Timing_wheel_face.jpg http://www.autosportlabs.net/images/8/8a/Timing_wheel_mounted.jpg images taken from http://www.autosportlabs.net Or talk to Gintsk, scroll down and you'll see: Toyota AE 86. GT25 bb turbo. Fully sequencial on stock 24+1 VR sensors. Active COPs from VAG driven from stepper chip. For drift. http://www.vems.hu/wiki/index.php?page=MembersPage%2FGintsK%2FSuccess --- My harness is just about done. I need to wire up the wideband sensor and its all done. This is my most recent pic: http://i244.photobucket.com/albums/gg11/JJGP2/4AGE20V/Picture052.jpg I'll be running COPs from a 1ZZFE Avensis but I'm not sure if I can run the stock revcounter using their tach signal http://www.boostedmiata.com/FAQ/cops/cop_pins.jpg (Found on a miata forum) 1 ground 2 trigger 3 tach 4 +12V Any thoughts?
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.