###      
 ## ###  
 ## #    
 #####   
 ## ##   
 ##  ##  
#### ### 
         

         
  ####   
     ##  
  #####  
 ##  ##  
 ##  ##  
  ### ## 
         

  ___  
 / _ \ 
/ /_\ \
|  _  |
| | | |
\_| |_/
       
       

 _______ 
(       )
| () () |
| || || |
| |(_)| |
| |   | |
| )   ( |
|/     \|
         

         
         
 #####   
 ##  ##  
 ##      
 ##      
 ##      
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
'''Yugo C20LET''' My first page here will be actually my last project. It's a small car made in Serbia with well known c20let engine from Opel Calibra turbo. Goal was to make a car run as it should with Vems in less than ten days (tenth day was drag race in Osijek, CRO). All wirings were made according to Phat Bob guide, like all others car I installed Vems before, luckily without any problems. Harness was made of 0.75mm2 automotive grade wire, with exception of ground wire 6mm2. MAP and MAT sensor used for this install was Bosch 0 281 002 401, same from webshop, with difference in range of it. In webshop you can find it's 300kPa sensor, while actually its 330kPa sensor. ---- '''Primary Trigger''' * standard VR sensor * stock 60-2 trigger wheel * 19 teeth before TDC Secondary trigger was taken from Astra F GSI which uses DIS module. ---- Ignition subsystem was wasted spark DIS module droven with two IGBTs. Injection was fully sequential, made also according to PhatBob guide, with Siemens DEKA 630cc injectors used, and with 30v flyback diode installed. Firmware used in this case was 1.0.78 because of possibility of using ignition retarding when using NOS, with only input configured. ---- Two more inputs were used for launch control and flat shift (aka shift cut), configured to cut only spark while shifting gear, with 250mS used as longest period of cutting. Be careful when playing with launch control, you could destroy your exhaust system, dramatically shorten turbos life and make very high EGT ---- ---- '''VW Corrado VR6 Turbo''' * to do. Waiting for a postman with Vems in hands. ---- ---- '''Fiat Coupe 20VT''' * successfully done, need some time to write... ---- ---- '''Fiat Coupe 16VT''' * to do, just ordered Vems for it ---- ---- '''Escort RS Cosworth''' * successfully done, with a looooot of problems, need some time to write... ---- ---- '''Kadett D MV6''' * unfinished, will finish/write about it after painting :) ---- ---- '''Fiat Punto 1.4GT gt2871r''' * successfully done, after that upgraded turbo and injectors, will write later... ---- ---- '''Tuned Yugo 55''' * A little waste of money and time my team is working on :) Will write about it when it's finished ---- ---- '''Kadett C C20XE''' * Old rusty car, XE for now, will be LET soon :) ---- ---- '''Highly tuned Suzuki Swift GTI''' * To do. Collecting parts for it. Slide throttle bodies, 340 deg/10,5mm cams, lightened, polished and balanced crankshaft, very light pistons, and a lot of funny parts :)
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.