|\     /|
| )   ( |
| (___) |
|  ___  |
| (   ) |
| )   ( |
|/     \|
         

         
         
 ##  ##  
 ##  ##  
 ##  ##  
 ##  ##  
  #####  
         

   ##    
   ##    
 ######  
   ##    
   ##    
   ##    
    ###  
         

 _    _ 
| |  | |
| |  | |
| |/\| |
\  /\  /
 \/  \/ 
        
        

         
         
  #####  
 ##  ##  
 ##  ##  
  #####  
     ##  
 #####   

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
#I can't find a page/diagram for assembling my Genboard, where can I find it? ## Most of it is done when shipped. http://www.vems.hu/index.php?page=BuildProcedures%2FSectionThree is the best place to start as far as I know. The http://www.vems.hu/index.php?page=GenBoard%2FManual is starting to get filled in quite well, so be sure to check that out too. ## I've read through those pages, and my understanding is that the only things I need to add to my genboard are the FET's, IGBT's, and MAP sensor. If I plan on using the connections in the above table (thanks for the help filling it in!) where do I solder the parts? I've found holes for the MAP sensor, but which way is it inserted? One pin has a notch, is that pin1? ### Try this: [http://www.vems.hu/files/genboardv3/images/genboardv3.1_output_labels.jpg Output Diagram] I just made it and uploaded it. Not great because I was in a hurry, but should suffice for now. Also for the MAP sensor, you're right. The notch is pin1. Pins 1,2,3 on the board are the pads with traces attached to them. ## Thanks for the diagram, exactly what I needed. Do the FET's and IGBT's have a pin1? yes, pinout is GDS (gate, drain, source). Which way are they oriented? this way. Actually, every component has a datasheet, it's often helpful to check that if in doubt. I assume they need a heat sink? FETs dissipate very little heat, but IGBTs dissipate more, especially with a distributor setup. Do you stick it to a piece of aluminum or something? the IGBTs need to be insulated from the heatsink. Anything else I should know? Hey, at least I know how to solder :) ## Found this [http://www.american.hu/GenBoardv31/GenBoardv31_assembled/Genboardv31_assembled_0010.jpg Here]so I soldered them like this http://www.headcasestudios.com/genboard/my_genboard_bottom.jpg #My stock ignition is a Bosch Coilpack //(part# F6000-51838?)// I'm pretty sure it has dwell control. Which genboard outputs do I use, how do I assemble my Genboard for this? ## I'm not sure on the coilpack dwell control, but drive00, 01, and 02 will work fine. Actually drive_00 through drive_07... just pick 3 you like. ;-) If your coilpack doesn't do dwell, it's really easy to control via Genboard. #I've got 2 weeks off starting tomorrow (Jul16), and having my car running with genboard is my vacation project! ## Being organized is key. Don't rush it just to get done. You got your board already? I'm impressed! I just sent it on the 13th.
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.