### ## ## ## ## ## #### ## ## ## ##
_ | | | | | | | |____ |______|
#### # # # # # ####
_ __ | | / / | |/ / | \ | |\ \ \_| \_/
### ## ### ## # ##### ## ## ## ## #### ###
IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now. Visit Preferences to set your user name Summary of change: Hallo I am from Denmark and I am planing to use a V3.2 on my VW Golf GTI 8V. MembersPage/HansK/IgnitionSetup MembersPage/HansK/EgoReadingProblems MembersPage/HansK/History ------------- 2005.07.16 Q.1) Does the MAPdot work fin, and should it be a certain firmware/megatune I use? Q.2)When i open my Lambda Table in MegaTune (r18 and Firmware 1.0.12) the numbers are all wrong.. http://www.vems.hu/files/HansK/Lambda_Table.jpg I can get the same numbers out of the board again with the Terminal-program as I put in.. But they don't show in MegaTune??? The numbers I put in the Tables-file was: l[0]=4E 3B 39 38 38 38 3B 3B 3B 3B 3B 3B l[1]=4E 3B 39 38 38 38 3B 3B 3B 3B 3B 3B l[2]=4E 3B 39 38 38 38 3B 3B 3B 3B 3B 3B l[3]=4E 3B 39 38 38 38 3B 3B 3B 3B 3B 3B l[4]=4E 3B 39 38 38 38 3B 3B 3B 3B 3B 3B l[5]=4E 3B 39 38 39 39 3F 41 41 41 41 41 l[6]=4E 3B 3B 39 3B 3B 3F 44 44 44 44 44 l[7]=4E 3D 3D 3B 3D 3D 3F 48 4E 4E 4E 4E l[8]=4E 3F 3F 3D 3F 3F 41 48 4E 4E 4E 4E l[9]=4E 41 41 3F 3F 3F 42 4C 4E 4E 4E 4E l[A]=4E 41 41 41 41 41 44 4C 4E 4E 4E 4E l[B]=4E 41 41 41 41 41 44 4C 4E 4E 4E 4E Q.3) If I download the new Firmware 1.0.14 to the board, I want to to do some new testing on the table but now I mounted all the transistors in the box.. Should I just put a lightbulb on all the outputs or what to do?? What Firmware version can be recommended? ------------- Please post your config.txt so that others can review and hopefullly learn (especially me ;) Thank you. http://www.vems.hu/files/HansK/Config.txt It is not in use yet so don't put too much in it, but you are welcom to give input. ------------- 2005.06.19 Q.1) I have a 2-pin idle-valve, but what settings should be used fore this.. PWM, ON/OFF? Any solenoid works with ON/OFF. Only some work (well) with PWM. ** what is resistance ? ** anything known about original application? Does it have real idle-air control or just simple "fast-idle" ? Does some one use the the same valve, and have a config-file that I can see or just some input to what settings to use? http://www.vems.hu/files/HansK/P6220090.JPG Q.2) Is there some way to test the idle-output? ** which output did you choose in iac_sol_channel ? ** PWM type iac output can be tested with forced iac.position: mdi01..mdiff . Do NOT forget to set back to mdi00 (or reboot) after you executed the tests to revert to normal control. ** alternatively it can be tested like any other digital output, with mdh.. command. See GenBoard/Manual/DigitalOut/Table. In this case, do NOT forget to set iac_sol_channel=FF to prevent interference and set it back after the test. 2005.06.01 I got the new Megatune "mt-r014" and I tryed to use the firmware that was together whit it, but then I got no "output" on inj. or ign. and the the config and table was the same..? '''No problem..''' Just needed to chance secondary_trigger to "02" instead of "FF". Optional: Add document to category: Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.