______ 
 |  ____|
 | |__   
 |  __|  
 | |____ 
 |______|
         
         

   _____ 
  / ____|
 | (___  
  \___ \ 
  ____) |
 |_____/ 
         
         

         
### ##   
 ### ##  
 ##  ##  
 ##  ##  
 ##  ##  
#### ### 
         

         
  #### # 
 ##  ##  
 ##  ##  
 ##  ##  
 ##  ##  
  #####  
     ### 

         
         
  ####   
 ##  ##  
 ##      
 ##  ##  
  ####   
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
The car is a Kadett C with a Calibra 2,0 16V C20XE engine mounted. ----------- 2006.09.28 MT also say "trigger-errors" when I'm using stimout (mstBAmsp02) :( ?? I listed my trigger-settings at the bottom af the page. The only thing I'm not sure abouth is "trigger_tooth". I've seen both 02, 08 and 10 in others config-file (with 60-2 tigger). What does it mean? Can any one see any thing wrong with my ttrigger-settings? 2006.09.25 I tryed using stimout generating a 60-2 trigger signal to trigger the board. I did not see RPM in display going to 0000rpm once in a while like when using wave-file from PC made by "Trigger signal generator". * after using Terminal (eg. to start stimout), you need to say bye (say byebye -lowercase! - just to be sure, it'll respond with Bye). Other wise you will NOT be able to connect to MT (MT says "trigger-errors" if the W.. counter is above 10 on mlp01 LCD page). Any one who has experienced similar problem when using "Trigger signal generator"? http://www.vems.hu/wiki/index.php?page=ElectronicDesign%2FTriggerSignalGenerator * make sure to use a recent version, preferrably the one that takes 100-300-8000 format and makes output filename itself (from the input options). I use audacity (on windows and linux too) becuase it's easy to verify waveform ** I don't know what version it is, I just downloaded the one that is linked to on the WinTools page: http://www.vems.hu/files/TuningSoftware/SignalGenerator/signalgen.zip 2006.09.19 I have tried changing threshold on LM1815 with out luck. I'd like to try to use the board to generate the trigger-signal http://www.vems.hu/wiki/index.php?page=OutputTrigger but I '''need''' firmware V1.0.53 where '''MY_CONF += -D WOT_OUTPUT_TPS_THRESHOLD''' is enabled in the my_make file. Hans, a firmware image with that compile option is not needed stimout is still available on the channel you select for the wot_output (for example p259, 5) outputs the pulsetrain on the fuelpump pin; (dont use the same channel for fuel_pump when using it for stimout), dont forget to add an inline series cap from stimout pin (needs to be pulledup with resistor to +5v) when feeding it into the primairy trigger pin - DB Thanks! 2006.09.13 The engine has a 60-2 trigger wheel on crank so I tried to trigger the board with the signal-generator generating a 60-2 signal (m582 1740 200 20 1000 1000) but MT shows "trigger-errors", and a datalog shows random 0RPM one or two times every second. http://www.vems.hu/files/HansK/datalog200609122217_trigger_errors.xls I'm using firmware/MT 1.0.53 --------------- Config: <code> primary_trigger=01 #toothed wheel and VR sensor secondary_trigger=02 #disabled tooth_wheel=3A #58 teeth (60-2) trigger_tooth=08 #should it bee 02, 08 or..? explanation please. another_trigger_tooth=1E crank_minper=50 tooth_wheel_twidth1=6 tooth_wheel_twidth2=12 cam_sync_r_edge_phase=FF cam_sync_f_edge_phase=FF reset_engphase_after=FF #? ign_tdcdelay=9A ign_dwell14=3E ign_dwell6=60 ign_crank_advance=50 ign_out=70 ignchmax=01 # wasted spark </code> ------------------ MembersPage/HansK
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.