##    
         
  ###    
   ##    
   ##    
   ##    
 ######  
         

         
#### ### 
 ##   #  
  ####   
  ###    
 #  ##   
###  ### 
         

 __   __
 \ \ / /
  \ V / 
   | |  
   |_|  
        

         
##  # ## 
##  #  # 
 ## ## # 
 ### ##  
  ## ##  
  #   #  
         

 _____ 
|  __ \
| |  \/
| | __ 
| |_\ \
 \____/
       
       

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
2006.04.24 I was trying/testing idle-channel output using two different channels. Useing Step A "output" was always on (0% TSP of course) even before I started trigger-signal.. Useing SPECFET1 I never got any output (selected in MT), and it is mounted. Beware that flyback diode is needed for specfet when driving inductive load like a solenoid! - Yes was just testing with scope.. Connect a diode (like 1n4007 or BY399 or ES2J or similar) * anode to switched point of the solenoid (channel output, EC18-pin..) * cathode (marked with a line) to the other pad of the solenoid: the same where you connect the positive +12V (switched and fused) power '''Q:''' What output channel is recommend fore idle-valve (2-pin VDO-valve)? http://www.vems.hu/files/HansK/P6220090.JPG * a free injector channel is most common * or a stepper output because these have onboard flyback by default. - Okay I'll just stik to the stepper-output, mount a injector-fet next time the box is out.. thanks ------------- 2005.11.16 I finaly got time to work on idle.. and it works!! :) I just got a question about some settings: * "iac_conf RAW" under Idle setting in MegaTune ** it's the "packed" value of several IAC related flags: (from global.h or varstr.h / magicstr.h): ** ''uint8_t iac_conf; // iac, bit7:softidle bit6:asym bit5:dualsol bit4=1:ignadv ON, bit3:preciseidle bit 2:stepper(0=pwm) bit1:low_power_halt bit0:power_iac_only_when_move'' ** when you're on the phone, it's much easier to instruct someone to read (or set to a particular value) this value than list all the options. * iac_conf=18 (decimal 24), which means bit4 and bit3 are set: ignadv based advance is ON; preciseidle is ON (but not stepper, so PWM-solenoid) * And how does "IAC afterstart, step per 160rpm" work? ** iac_afterstart_step was a hint to the ECM of how much added opening is required. Use very low value, 1 or 0. It's ripped from recent firmwares. What firmware do you use ? v.13 or so.. ** value of 4 means: If you configure +200 "afterstart" RPM, +5 (=4 * 200/160) will be added to the iac reference position. '''0 is reasonable''', the PID integral (I-term) should have no problem reaching the higher RPM. --------------- MembersPage/HansK
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.