_      
 | |     
 | |     
 | |     
 | |____ 
 |______|
         
         

         
         
 #####   
 ##  ##  
 ##  ##  
 #####   
 ##      
 ##      

 _______ 
(  ___  )
| (   ) |
| |   | |
| |   | |
| | /\| |
| (_\ \ |
(____\/_)
         

         
         
 ######  
    ##   
   ##    
  ##     
 ######  
         

  _____  
 |  __ \ 
 | |__) |
 |  _  / 
 | | \ \ 
 |_|  \_\
         
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
I use a datalogger and dash from the company '''Race Technology''', labelled "Vems interface" * '''requires reflash of the interface''', after that '''THE RACE TECHNOLOGY VEMS INTERFACE IS NOW WORKING CORRECTLY, AND READS THE AIM SIGNAL FROM THE V3''' ** the reflash was provided by Race Technology (thanx) ** can we publish the firmware that is required for the [http://www.race-technology.com/dash2_2_31.html Race-Tech Dash2] display ? There were a couple of disappointed Race-Tech owners who gave up, and will be very happy to be able to use it finally. One dash-2 owner kindly offered his device for testing. Here is the reflash, which I got from Race Technology. It's not for the dash2 itself, it's for the Vems ECU Interface. '''CONFIRM WITH RACE TECHNOLOGY BEFORE REFLASHING YOUR INTERFACE''', otherwise this could probably brick the interface! [http://www.vems.hu/files/HankMoody/VEMS%20AIM%20protocol%20customer%20reflash%20130225.zip] ---- '''Protocol details''' * VEMS firmware sends data via [http://www.vems.hu/files/MembersPage/NanassyPeter/AIM_support/AIM-ECU_protocol.pdf AIM protocol], ** the scalers were made according to [http://www.vems.hu/files/MembersPage/NanassyPeter/AIM_support/AIM-ECU%20protocol.pdf AIM-protocol.pdf] with only minor corrections to match the Race-Tech Motec interface (which was found to deviate slightly from the protocol.pdf, eg wheelspeed 10x multiplier). ---- Other channels: Example of data streamed from my v3: http://www.vems.hu/files/HankMoody/aim-new%20hypertrm.TXT It seems there are more channels streaming from my v3! I also see activity on channels 224-229 in my data. What are theese channels used for? * '''I also see action on channel 133, what is that used for?''' ** '''GPSSPEED''' is sent via channel-133 (5+128 if you like... 5 is traditional wheelspeed) ** valid when nmea-GPS is connected ** Of course, GPSSPEED might be different from wheelspeed: likely more precise on the average (not depending on user calibration and tire pressure), but filtered more agressively, slower response. * 224-229 are AIM_OUT_0 .. AIM_OUT_5, custom outputs ** eg. boostcontrol solenoid output channel, idle solenoid output channel can be actuated by other device, say, round if configured so (very useful on V8 where ++ number of outputs help) ** .. channel=Xe where (X=0..5) ** disable outputs by i7, not by i6 (unless you know what you are doing) ** we'll review your vemscfg in this respect ** however any AIM receivers just neglect the channels they don't know. Chance is 0.00% that disabling 224-229 will get Race-Tech working if it does not work with 224-229 transmitted. ---- Im running v3 firmware 1.1.96 Some of the channels within the AIM datasream are correct. * TPS displayed good (AIM channel 45) * RPM (sent by VEMS in AIM channel 1). '''Examples sniffed in hex from terminal''' - shows vems firmware sends correctly: ** (03EB=) 1003RPM - 01 A3 03 EB 92 ** (07D6=) 2006RPM - 01 A3 07 D6 81 * [http://www.race-technology.com/wiki/index.php/ECUType/VEMSECU VEMS-ecu interface] ** it says "Note: AIM protocol used" but it obviously is not using the [http://www.aimsports.com/products/mxl-chooser.html AIM - RS232 protocol] that v3 properly sends (when enabled) ** it also says conflicting info at the same place: "The VEMS ECU outputs 56 byte sequence of data at 19200bps baud rate." - this suggests the Race-Tech display does NOT actually use AIM, but '''relies on the 'A' command''' that old firmwares (before 1.1.96) used for sending real-time data to VemsTune and megatune. (offsets found in global.h and megatune.ini, and everyone knows runtime data sending works, but for longterm compatibility AIM-RS232 is a much better choice to rely on). ** new v3 firmwares (eg. 1.2.x) only act on CRC-protected commands ("triggerframe protocol") to prevent corruption (due to serial noise). In other words it does NOT reply at all on non-CRC-protected commands like the 'A' command.
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.