______ 
|  ___|
| |_   
|  _|  
| |    
\_|    
       
       

  __  __ 
 |  \/  |
 | |\/| |
 | |  | |
 |_|  |_|
         

         
     ##  
         
     ##  
     ##  
     ##  
     ##  
  ####   

 ##      
 ##      
 ##  ##  
 ## ##   
 ####    
 ## ##   
 ##  ##  
         

    ##   
         
    ##   
    ##   
    ##   
    ##   
    ##   
  ###    

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
'''Issue''' IGN output behavior changes with RPM and # of cylinders. * Firmware 1.0.23, Megatune r27 and r30 all show same results * Firmware is precomiled from website version 1.0.23 '''History''' I found this issue when attempting to functional check a unit prior to configuration. Initial reports suggested that it was a bad trigger signal (benchtop generation). Resolved this problem and '''now can generate a proper 60-2 wheel VAG style without any wheel count errors.''' '''mcel.. if you change your IGN outputs to 00 01 02 03 04 05 06 07 instead of 00 01 00 01 00 01 00 01 you can recreate the error with your config ''' '''Description of issues''' * Given: [MembersPage/GrmRacer/TurboSetup/TurboConfig Config] firmware, and tables ** there is an output channel conflict: misc1out_channel=06 and misc2out_channel=06. Also, you might want to change the disabled channels for FF (although xF shouldn't cause problem) ** divider=02 why ? (should be 01 right ?) ** try to configure tooth_wheel_twidth1, tooth_wheel_twidth2 and reset_engphase_after properly (although shouldn't matter with secondary_trigger=02 thus disabled) * Issue is a function of # of cylinders, RPM, and default Megatune IGN output behavior. * Under Idle conditions, ie. < 1500 RPM for a wasted spark ( 2 outputs alternating) works fine for any setting. If the RPM goes above a threshold (41Hz for 4 clyn, 29Hz for a 8 clyn). the output changes to include other non-configured output. '''Current experiment''' Reflash VEMS v3.3 with new firmware 1.0.23 first then use the latest release. Firmware version 1.0.23 as downloaded from filethingie * no recompilation done * configs & Table changed using MegaTune (r30) only * pretending to be end user trying to get board setup * I also don't want to go thru the toolchain setup to do it. ---------------- Problem is that the number of outputs driven changes when a factor of RPM and # of clyns and #of IGN outputs selected '''Original configuration to find problem''' Basic description is the Ingnition outputs were set in ''Ignition Settings'' Outputs to use in h[2] set to [7..0] *Ingnition ouputs set to **0 Drive00 **1 Drive01 **2 Drive02 **3 Drive03 **4 Drive04 **5 Drive05 **6 Drive06 **7 Drive07 ''Yes I know this is not valid for a wasted spark BUT, it produces bad output. '' **above 41Hz(~2500rpm) with an 8 clyn setup. Note that another_trigger_tooth=1E doesn't seem good for 8cyl. Please provide all the configs you used. **above 29Hz(~1650RPM) with a 4 clyn setup Symptom above these values all IGN outputs that are set are triggered else only 2 outputs are triggered. ''if Ignition Settings '' *outputs to use in h[2] is set to [1..0] symptom goes away. '' if Ignition Settings '' *outputs to use in h[2] is set to [2..0] three outputs trigger above 41Hz(4clyn) '' if Ignition Settings '' *outputs to use in h[2] is set to [3..0] four outputs trigger above 41Hz(4clyn) * * '' if Ignition Settings '' *outputs to use in h[2] is set to [7..0] 8 outputs trigger above 41Hz(4clyn) ----------------- '''Emils report''' triggering the board at 2000 rpm, trying to reproduce GRMracers report of strange ignition outputs 2000 rpm, 60-2, tried with ignchmax = 03 or 07, same result based on marcell's example config * at 2000 rpm, it works properly with dwell >= 2.82, but with 2.75mS or less, only 2 outputs is driven * if i then lower TDCdelay from 56 to 55 degrees, all outputs turn back on * with TDCdelay = 55, only 2 outputs are active with dwell anything lower than 2.75 mS *with TDCdelay = 50, dwell below 2.30 mS will give the same result
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.