_    _ 
( )  ( )
`\`\/'/'
  >  <  
 /'/\`\ 
(_)  (_)
        
        

         
         
  ####   
 ##  ##  
 ######  
 ##      
  ####   
         

  ___ 
 |_ _|
  | | 
  | | 
 |___|
      

         
         
 ##  ##  
 ####### 
 ####### 
 ## # ## 
 ##   ## 
         

         
         
 #####   
 ##  ##  
 ##  ##  
 ##  ##  
 ##  ##  
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
== For those new to VEMS, the ECIII header on these tables is just the name for the large connectors on the VEMS box. Number in setup refers to the name of the function when using MegaTune. == ---- == Power == ---- |||||||| '''Power''' || || '''Wire Color''' || '''Use''' || '''number in setup''' || '''ECIII pin''' || ||Black/Red|| EFI Relay #1 ||+13.8VBATT || 25 || |||||||| '''Grounds''' || ||'''Wire Color''' || '''Use''' || '''number in setup''' || '''ECIII pin''' || ||Black || ground to CLT || GND || 26 || ||Black || power grounds || GND5 || 32 || ||Black || power grounds || GND5 || 21 || ||Black || power grounds || GND5 || 5 || == TPS == |||||||| '''TPS switch''' || || '''Wire Color''' || '''Use''' || '''number in setup''' || '''ECIII pin''' || || Red || Wiper || TPS || pin1 || || Light Blue/Red || PWR || TPS5V || pin28 || || Brown || common || GND || pin26 || || Light Blue || Switch || || || == Injectors == |||||||| ''' Injector ''' || || '''Wire Color''' || '''Injector''' || '''number in setup''' || '''ECIII pin''' || || Yellow || Injector power || EFI Relay || || || || Injector #1 || INJA || pin7|| || || Injector #2 || INJB || pin19|| || || Injector #3 || INJC || pin8|| || || Injector #4 || INJD || pin20|| == Coils setup == |||||||||||| The pairs I will use so I can run wasted is || || '''Wire Color''' ||Transistor || number in setup || ECIII pin || cyl || || ?? || Q16 || #0 || pin35 || 1,4 || || ?? || Q21 || #1 || pin33 || 2,3 || == CLT == || '''Wire Color''' || '''Use''' || '''number in setup''' || '''ECIII pin''' || || ?? || CLT || CLT || 14 || || Black || Gnd || Gnd || 26 || == IAT == || '''Wire Color''' || '''Use''' || '''number in setup || ECIII pin''' || || Yellow/Black || || MAT || 2 || || Black || Gnd || Gnd || 26|| == CAM Trigers == |||||||| '''CAM Trigers''' use coex || || '''Wire Color''' || '''Use''' || '''number in setup''' || '''ECIII pin''' || || Ne || coex || TRIGG1_CONN || 27 || || G1 || coex || TRIGG2_CONN || 13 || || G- || shield || GND || 26 || == WBO² == ground the green coex to gnd |||||||||| '''WBO²''' || || '''Wire Color''' || '''Use''' || '''ECIII18 pin''' || '''WBO² pin''' || || ?? || PUMP(-) || 7 || 5 || || ?? || PUMP(+) || 9 || 6 || || coex|| NERNST_CELL1 || 13 || 1 || || ??|| HEATER1(-) || 18 || 4 || || ?? ||Power || N/A || 3 || |||||||||| Power will come from the old wire that went to the NBO²|| == Tachometer == ||||||||||'''Tachometer''' || || '''Wire Color''' || '''Use''' || '''number in setup''' || ECIII18 pin || || ?? || goes to cluster(tach) || STEP_B || 10 || == Knock == |||||||| '''Knock''' Use coex|| || '''Wire Color''' || '''Use''' || number in setup || ECIII pin || || ?? ||KNOCK1 || || 34 || || Shield || Knock gnd || || 36 || == Fan == |||||| '''Fan Reley''' || || '''Wire Color''' || '''Use''' || '''ECIII18 pin''' || || ?? || STEP_C || 5 || == Fuel Pump Power Control == ||||||'''Fuel Pump''' || || '''Wire Color''' || '''Use''' || '''number in setup''' || '''ECIII pin''' || || Green/Red || relay || STEP_A || small#4 || == IAC == Need to add a flyback diode between the pins? || '''Wire Color''' || '''Use''' || number in setup || ECIII pin || || ?? || will be the IAC control || INJG || pin6 || || ?? || will be the IAC control || INJF || pin18 || || ?? || Switched power || N/A || N/A || == Check Engine Light == || '''Wire Color''' || '''Use''' || number in setup || ECIII pin || || Green/White || ?? || ?? || ??|| == Serial Port == || '''Wire Color''' || '''Use''' || '''number in setup''' || '''ECIII18 pin''' || || Red || RxD || RxD || 14 || || Brown || TxD || TxD || 15 || ---- ''' C BLACK firewall connector ''' http://www.vems.hu/files/GrantHendricks/C_plug.gif NOTE: Pins may have different uses on other trim models/year of AE86. This is specifically for a 1986 US spec "Kouki" GT-S with 4AG-EC (16V with EFI). Generally, auto transmission uses pin 8 for coil and igniter power and leaves 14 blank, Manual transmission uses pin 14 for the same purpose and leaves pin 8 blank. Will add the remaining pins tomorrow.
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.