______ 
| ___ \
| |_/ /
|  __/ 
| |    
\_|    
       
       

  ___  
 / _ \ 
/ /_\ \
|  _  |
| | | |
\_| |_/
       
       

 __          __
 \ \        / /
  \ \  /\  / / 
   \ \/  \/ /  
    \  /\  /   
     \/  \/    
               
               

   ___ 
  |_  |
    | |
    | |
/\__/ /
\____/ 
       
       

         
         
  ####   
 #    #  
 ######  
 #       
  ####   
         

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
'''Golf II 1.8 16V GTI''' (motorcode KR 139 Le) * want to convert to gasoline-LPG * currently NA, but later turbo Assembled ECU features: * Flyback 30V flyback * ignition driver 6+2 * MAP connection 300kPa onboard (6/4mm pneumatic) * '''primary_trigger HALL''' * '''secondary_trigger HALL''' * 1-wire interface no * Knock and EGT yes * LCD connection yes * PS2 connection yes * mounting-style screws '''Az ECU adatai''' *Board version-3.3 *Serial nr;1072 *pump;4.11V *wbo2 pump pw zero;0x67 *wbo2 nertstdc target;0x87 *pump+; +1.3mv/200 Ohm *AREF;4.9V *(C103;1nf, no D100) *frimware;1,0,73 MembersPage/GolfGtiLpg/SenzoR MembersPage/GolfGtiLpg/IdleAir MembersPage/GolfGtiLpg/KapcsLpg MembersPage/GolfGtiLpg/GYujtas MemberPage/GolfGtiLpg/InJektor MembersPage/GolfGtiLpg/PinOut ---- '''Launch control''' Just like for the gasoline switch, pull an mcp3208 analog input to ground. See EC18pin12,6,16 mcp3208 analog inputs in WebShop ECU specs, all are available in your case. Measure if they are pulled up to +5V internally * mcp3208ch6 and mcp3208ch7 inputs might be pulled to +5V via 2k7 internally depending on how you requested. If so, no need for external pullup resistor in the harness ** in any case, be very careful: pull to +5V gently, or to ground with a switch. These inputs are not protected agains +12V ! +12V on mcp3208 input would ruin the controller. ---- wiring http://www.vems.hu/files/GolfGtiLpg/bekotes.xls schematic http://www.vems.hu/files/GolfGtiLpg/bekotesi%20rajz.jpg ---- '''Config and tables''' Initial (not running yet) config and tables [http://www.vems.hu/filethingie.php?action=list&subdir=MembersPage/GolfGtiLpg/etc here] Review (check hints on these pages) 1.1.27 will NOT work with 4-1 (only 12-1 or more tooth supported with missing tooth setup because of tooth_wheel_twidth2 semantics). 1.0.73 is the only choice for now....
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.