____  
 | __ ) 
 |  _ \ 
 | |_) |
 |____/ 
        

 _____ 
|  ___|
| |__  
|  __| 
| |___ 
\____/ 
       
       

 _____ 
|_   _|
  | |  
  | |  
  | |  
  \_/  
       
       

 _______ 
(_____  )
     /'/'
   /'/'  
 /'/'___ 
(_______)
         
         

 _____ 
(_   _)
  | |  
  | |  
  | |  
  (_)  
       
       

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
Hello! About this engine: this is small stroke 6cyl engine with aggressive cams and target redline at 8000rpm! This project definitely need '''overlapping dwell control'''. 2ms dwell will be too small. '''Q: Will Genboard have this feature in near future? When? Thanks!''' ---- '''Please add your coments for my first VEMS project.''' Here is inconvenient to find rigt thread for newbie... :( For first want to put VEMS on BMW M50 modified engine with COPs for dragrace. It is 6cyl 24V DOHC engine bored up to 3L. Deeply rebuilded head, very agresive cams for this stroke. Custom make intake system with large reciever. And more. *'''Why I want to put VEMS because:''' ** 1)COP (general) ** 2)WBO2 on board ** 3)sequential injection *'''What features I can't find:''' ** 1) Launch control! ** 2) traction control for beter acceleration control in first gear(rough like MSnS-Extra have) ** 3) '''ignition retard due hot intake and advance for cold engine.''' Second feature I have found very useful on my daily stand-alone equiped car. But I can't found it here. ** 4) two engine maps ('street fuel/race fuel' alike) ** 5)progressive shift ligts. and more All of theese functions is useful or even prerequisite for succeseful drag with revy engine. '''Q: Is here code for some of theese useful functions?''' A: There is a function called AntiLagSystem in which you can retard the ignition advance and add fuel, this is to give more boost off the line. Progressive shift lights can be made with the "misc outputs", check the MegaTune software. GK: Thanks. It is little better ---- '''Q: Is today from MegaTune is reachable all functions? And there is nothing else?''' MegaTunix is an alternative, but no longer in development as far as I understand it. OtherTuningSoftware/PSITuner could turn out good. MegaTune can be used for all functions, with a few reservations that I can't remember of the top of my head. ---- *'''My shopping cart looks so:''' **1 x VEMS sticker **1 x Alubos EC frontplate **2 x Alubos gasket **1 x Alubos Endplate **1 x Alubos1600 **1 x Additional VR or Coil interface (both sensors is VR) **1 x Dual channel knock sensor interface (just for experiment) **1 x EGT input amplifier (just for experiment) **1 x Econoseal18-PCB **1 x Econoseal18-Wire **1 x Econoseal36-PCB **1 x Econoseal36-Wire **7 x Ignition driver **8 x Injector or WBO2 heater driver **1 x Wideband O2 sensor **1 x Ignition driver insulator sheet **1 x LCD4x20 **1 x Wideband connector **1 x Genboard v3.3 **1 x PS2 keyboard extension cable **1 x Serial jack kit '''Q: Is thomething miss here?''' A: Why not fully populate the board with 8 ignition drivers (IGBT) ? You naturally need 1 injector driver per injector (8 max), the two superfluos drivers can be used for misc outputs or other high power usage on your 6 cyl engine. As you will build the board+case yourself, I recommend buying a few misc parts for connecting the serial port, LCD and EGT (cable + connectors). '''Q: What high current circuits you mean???''' A: Idle air solenoid, the stock unit on older M20 engines need two drivers that can handle at least a 1A load with flyback (coil load). I don't know about what comes with the M50 engines, I think the unit is hidden below the intake manifold. ---- GK: EGT is not priority. ExhaustGasTemp should be a priority for you, it lets you know you're safe and is a very good tuning tool. ---- Q: May be better is to put Genboard PCB inside Motronic ECU? A: The Genboard case is much easier to work with and will allow better cooling/clamping for the injector (FET) and ignition coil drivers (IGBT). I assume you have the 55 pin connector, it will be a lot of patch work to make it work with the original harness - it's a better idea to custom make your own harness, and within reason to also re-use some parts of the stock harness. ----
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.