###    
   ##    
   ##    
   ##    
   ##    
  ####   
         

         
   ##    
         
  ###    
   ##    
   ##    
  ####   
         

  ______
 |___  /
    / / 
   / /  
  / /__ 
 /_____|
        
        

  ###    
   ##    
   ##    
   ##    
   ##    
   ##    
  ####   
         

 _____ 
|  _  |
| | | |
| | | |
\ \_/ /
 \___/ 
       
       

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
'''Stage 3 - Control misc. devices''' * Control Idle solenoid - need to solve first, firmware development necessary, MembersPage/GergelyLezsak/IdleControl * Drive tachometer * Wire-in fuel-pump relay - done * Show oil temp. (No info on sensor either) * Control fuel consumption gauge (?) * drive a boost control solenoid * Install egt (hardware installation is tricky, need to remove the whole exhaust system) * Install knock sensor - No factory placement on M20 engine to mount, experiences are appreciated. ---- '''Tachometer''' As for driving BMW E30 series (inline 6 engine) tachometer, one needs to find out how original ECU (ie. Motronic) drives tachometer. Unfortunately I dont know driving signal waveform/type and hence currently can't help, reason because we did not measure orignal waveforms before dismantled original ecu and wireloom from car. But, if someone could measure... Engine speed output is routed from Motronic 'ECU (55 pin) connector' pin 6 and signal goes to instrument cluster pin A7. ---- '''Fuel Consumption Gauge''' * The actual gauge uses a linear voltage between 0 and 1.5 Volts. See my page here: MembersPage/MattiasSandgren/BmwEthirtyIx * You would need to bypass the electronics to get to it. * Could be used as a MAP gauge (10 litres/100km = 100 kPa). As what comes to controlling fuel consumption gauge, it seems that inside instrument cluster has some kind of adaptation module, which is engine type specific (size, number of cylinders etc.) - somehow it derives consumption from above mentioned tachometer signal and/or following two signals; * vehicle speed signal: from Motronic ecu pin 29 which also goes to the instrument cluster. * fuel rate output signal: from Motronic ecu pin 32 -> goes to instrument cluster pin A11. Don't know for sure, but 'Fuel rate output' signal might be some kind of pulses per second or pwm signal ? Someone could measure ? Hope these help ? I'm affraid we are talking about different motronic versions. Autodata catalog says that motronic pin 29 is ignition signal TO motronic. I can confirm that, since car was not running on motronic until I connected back that pin. Pin 32 is "throttle position control module" which might be some "tempomat" system. I'm not sure. I think my motronic didn't know the car's speed since my speedometer is fine without it :) (So signal from differential goes to the speedometer directly?) Instead, maybe the instrument panel calculates fuel consumption based on fuel rate signal and speed? Actually I only miss my tachometer, fuel cons. was inaccurate for ages (different size injectors and fuel pressure :) Thanks however, and I still seeking tachometer signal specifications. No one using factory tachometer? I guess I have to wire back motronic to measure somehow :( (or by phone# 1-2209238 in the evening)
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.