##    
         
  ###    
   ##    
   ##    
   ##    
  ####   
         

         
  ####   
 ##  ##  
 ##  ##  
 ##  ##  
 ##  ##  
  ####   
         

         
         
  ####   
     ##  
  #####  
 ##  ##  
  #####  
         

 ___   
(  _`\ 
| (_) )
|  _ <'
| (_) )
(____/'
       
       

  _____ 
 | ____|
 |  _|  
 | |___ 
 |_____|
        

IMPORTANT: enter the case-INsensitive alphabetic (no numbers) code AND WRITE SOME SHORT summary of changes (below) if you are saving changes. (not required for previewing changes). Wiki-spamming is not tolerated, will be removed, so it does NOT even show up in history. Spammers go away now.


Visit Preferences to set your user name
Summary of change:
'''Buy list''' Project 2: MembersPage/GergelyLezsak/BigSixTurbo Attila's E30 turbo (M30 3.4), mechanically in finish and preparing to control! * Assembled(?) GenBoard V3.3 set up with: ** complete alu case with all the plates and connectors ** 8 ignition conf ** 8 injector FETs always included ** 2 knocks and one EGT ** LCD and ps/2 ** off-board MAP ** normal flyback config * MAP sensor - external (MPX 2.5bar should be enough) ** we only have 4bar (packaged) enginebay-MAP. 2.5 bar only available onboard (at the moment). * Pressure hose (1 m) * IAT sensor (NTC) * EC36-Wire * EC18-Wire * LCD with wire * and a pair of DSUB9, some cable * WBO2 LSU4 sensor & connectors * some silicone wire * econoseal crimping tool * Wires and plugs -- got it (whole harness form junkyard) * Fuses and housing -- got it (whole harness form junkyard) * TPS sensor pot-style if necessary (maybe not) '''PINOUT request''' Requested deviant setup: pins which differ from webstore's [http://shop.x-dsl.hu/catalog/product_info.php?cPath=1&products_id=48 assembled controller] : * RS-232 : DSUB on endplate * MAP IN: EC36 pin29 (are you sure? - no, but mine is on it. If there's a new recommendation (EC18-pin6?) which doesn't hurt, then OK.) * KNOCK A & B ** Suggested EC18 pin2 and pin3 for knock. OK, let's go for recommended pins, BUT still we need to leave knock GND, to get both channels * extra ADC inputs ** EC18pin12 (well, standard, since seconardy trigger is HALL, not auditrigger) ** EC18pin14 and EC18pin15 can be extra ADC as well my (original) pinout is: [http://quasar.dynaweb.hu/~lezsi/bmw/conversion/lezsi-wiring.xls xls] ---- Project 1: my own E30 turbo (M20 2.5), project is almost done. * Wires and plugs -- got it (whole harness form junkyard) * Fuses and housing -- got it (whole harness form junkyard) * Silicon shielded wires -- got it (~5m) * M18x1.5mm/thread nuts to weld into exhaust (for wbo2) -- got it * MAP sensor (MPX 2.5 bar) -- got it * Pressure hose (1m) and T-shape. I've got 2 pipes from intake manifold both are d=4.5mm. One is for adj. FPR, one for boost gauge. -- got it * IAT sensor and some sort of mounting -- got it * GenBoard 3.3 and rescue kits * TPS sensor -- got it from junkyard, made mount from sheet of plastic * EC36-PCB -- got it on board * EC18-PCB -- got it on board * EC36-Wire -- got it * EC18-Wire -- got it * LCD with wire -- got it * and a pair of DSUB9, DSUB25 some cable -- got it * LM1815 chip for cam signal -- got it on board * ps2 extension cable * USB to RS232 * WBO2 LSU4 sensor & connectors -- got it * EGT K-Thermocouple and compensational wire -- got it * AD597 K-Thermocouple amplifier -- got it on board * TPIC8101 -- got it on board * 2x MCP3208 -- got it on board
Optional: Add document to category:
Wiki formatting: * is Bullet list ** Bullet list subentry ... '''Bold''', ---- is horizontal ruler, <code> preformatted text... </code> See wiki editing HELP for tables and other formatting tips and tricks.